BS 6348:1983
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Method for expression of the properties of signal generators
Hardcopy , PDF
20-04-2012
English
28-02-1983
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National foreword
Committees responsible
1. Scope
2. Object
Section One - Definitions
3. General terms related to generators
4. Values and ranges
5. Terms related to the expression of performance
6. Terms related to conditions of operation, transport
and storage
7. Terms related to frequency
8. Terms related to output amplitude
9. Terms related to the impedance at the outlet
10. Terms related to signal waveforms, distortions and
noise
11. Terms related to modulation
12. Pulse terms
13. Terms related to frequency sweeping
14. Terms related to unwanted effects
15. Additional technical terms
Section Two - Types of control of performance
characteristics
16. General
17. Specific types of control
18. Multiple control
19. Manual/programme control
Section Three - Expression of performance
20. Values and limits of error
21. Mandatory statements
22. Optional statements (limited by this standard)
23. Optional statements (not limited by this standard)
24. Specification of quantities
25. Form of the specification of stability error
26. Form of the specification of influence error
27. Methods of expressing error
28. Additional information
29. Quantities related to performance characteristics,
and the required statements and tests
Section Four - Verification of performance
30. General
31. Minimum verification tests for operating error and
intrinsic error
32. Minimum verification tests for stability error
33. Minimum verification tests for influence error
Section Five - General condition for testing
34. Measuring apparatus and methods
35. Period for achievement of stable operation
36. Preliminary adjustments
37. Connected load
38. Output amplitude
39. Control of influence quantities
40. Test categories
Section Six - Specific conditions for testing
41. Test conditions applicable to operating error
42. Test conditions applicable to intrinsic error
43. Test conditions applicable to influence error
44. Test conditions applicable to stability error
Section Seven - Specific test methods
45. Test methods required for certain quantities
Table I - Requirements for statements and tests on
quantities related to performance
characteristics of generators
Table II - Specified quantities to be subjected to
minimum test requirements for operating and
intrinsic errors
Table III - Specified quantities to be subjected to
minimum test requirements for stability
errors
Table IV - Specified quantities to be subjected to
minimum test requirements for influence
errors
Table V - Specified quantities to be subjected to
specific test methods
Gives essential definitions, establishes a selection of standard performance characteristics from which the manufacturers shall or may state requirements, and specifies tests to verify compliance with these requirements. Does not apply to pulse generators.
| Committee |
PEL/85
|
| DevelopmentNote |
Inactive for the new design. Also numbered as IEC 60716 Supersedes 78/28951 DC, BS 4980(1973), BS 5133(1975), BS 5134(1975) and BS 5826(1979) (09/2005)
|
| DocumentType |
Standard
|
| Pages |
50
|
| PublisherName |
British Standards Institution
|
| Status |
Withdrawn
|
| Supersedes |
| Standards | Relationship |
| UNE 54108:2000 | Identical |
| UNE-EN 12760:2000 | Identical |
| BS 4743:1979 | Specification for safety requirements for electronic measuring apparatus |
| BS 6146-2:1981 | An interface system for programmable measuring instruments (byte serial, bit parallel) Guide for code and format conventions |
| BS 5698-1:1979 | Guide to pulse techniques and apparatus Pulse terms and definitions |
| BS 4889:1973 | Method for specifying the performance of electronic measuring equipment |
| BS 5813:1979 | Guide for expression of the performance of pulse generators |
| BS 6146-1:1981 | An interface system for programmable measuring instruments (byte serial, bit parallel) Specification for functional, electrical and mechanical requirements, system applications and requirements for designer and user |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.