BS 6564-3:1990
Current
The latest, up-to-date edition.
Polytetrafluoroethylene (PTFE) materials and products Specification for E glass fibre filled polytetrafluoroethylene
Hardcopy , PDF
English
28-02-1990
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Committees responsible
Specification
0 Introduction
1 Scope
2 Definition
3 Designation
4 Composition and appearance
5 Performance and physical properties
6 Dimensional tolerances
7 Sampling
8 Marking
Tables
1 Forms, grades, subgrades and types covered by
BS 6465 : Part 3
2 Performance and physical properties
3 Tolerance on nominal outside diameter
4 Tolerance on thickness of sheet
5 Tolerance on nominal width and nominal thickness of
veneered tape
Appendices
A Information to be agreed between the purchaser and
the supplier
B Method for determining compression modulus
Specifies three levels of glass filling and two levels of performance.
| Committee |
PRI/82
|
| DevelopmentNote |
Supersedes 88/36032 DC. (09/2005) Reviewed and confirmed by BSI, December 2011. (11/2011)
|
| DocumentType |
Standard
|
| Pages |
14
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
This Part of BS 6564 specifies requirements for fabricated E glass fibre filled polytetrafluoroethylene (PTFE) products which may occur in several forms, available in the grades, subgrades and types as indicated in Table 1.
NOTE 1 E glass is defined in BS 3447 as “a glass containing not more than 1 % of alkali (calculated as Na2O) and used for the manufacture of glass fibres??.
NOTE 2 The titles of the publications referred to in this standard are listed on the inside back cover.
| BS 6564-1.1(1989) : 1989 | POLYTETRAFLUOROETHYLENE (PTFE) MATERIALS AND PRODUCTS - POLYTETRAFLUOROETHYLENE POWDERS FOR MOULDING AND EXTRUSION - SPECIFICATION |
| 04/30091878 DC : DRAFT FEB 2004 | BS EN ISO 13000-2 - PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 13000-2:2006 | PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS 6564-1.2(1989) : 1989 | POLYTETRAFLUOROETHYLENE (PTFE) MATERIALS AND PRODUCTS - POLYTETRAFLUOROETHYLENE POWDERS FOR MOULDING AND EXTRUSION - METHOD OF SPECIFYING |
| BS EN ISO 13000-2:2005 | Plastics. Polytetrafluoroethylene (PTFE) semi-finished products Preparation of test specimens and determination of properties |
| ISO 13000-2:2005 | Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 2: Preparation of test specimens and determination of properties |
| EN ISO 13000-2:2005 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005) |
| DIN EN ISO 13000-2:2006-02 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005) |
| BS 6564-2:1985 | Polytetrafluoroethylene (PTFE) materials and products. Specification for fabricated unfilled polytetrafluoroethylene products |
| BS 2782-3 Method 345A:1979 | Methods of testing plastics. Mechanical properties Determination of compressive properties by deformation at constant rate |
| BS 6564-1.1(1989) : 1989 | POLYTETRAFLUOROETHYLENE (PTFE) MATERIALS AND PRODUCTS - POLYTETRAFLUOROETHYLENE POWDERS FOR MOULDING AND EXTRUSION - SPECIFICATION |
| BS 2782-3 Method 327A:1982 | Methods of testing plastics. Mechanical properties Determination of tensile strength and elongation at break of polytetrafluoroethylene (PTFE) products |
| BS 3447:1962 | Glossary of terms used in the glass industry |
| BS 2782-6 Methods 620A to 620D:1980 | Methods of testing plastics. Dimensional properties Determination of density of solid plastics excluding cellular plastics (immersion method). Determination of density of solid plastics excluding cellular plastics (pyknometer method). Determination of density of solid plastics excluding cellular plastics (sink-float method). Determination of density of solid plastics excluding cellular plastics (density gradient column method) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.