BS 7008-1(1994) : AMD 8821
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ACQUISITION AND PRESENTATION OF COMPARABLE DATA FOR BASIC PROPERTIES OF PLASTICS - METHOD FOR SINGLE POINT DATA
23-11-2012
15-12-1995
Committees responsible
National foreword
Introduction
Method
1. Scope
2. Normative references
3. Definition
4. Specimen preparation and conditioning
5. Test requirements
6. Presentation of results
Annex
A. (informative) Bibliography
Tables
1. Moulding parameters
2. Test conditions and format for the presentation of
single-point data
Identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. Also gives detailed tables. BS AMD 8821 RENUMBERS THIS STANDARD
| Committee |
PRM/21
|
| DevelopmentNote |
Supersedes BS 7008-1(1988) Superseded and renumbered by BS EN ISO 10350 (09/1996)
|
| DocumentType |
Standard
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 10350:1993 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 75-1:2013 | Plastics — Determination of temperature of deflection under load — Part 1: General test method |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics — Multipurpose test specimens |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 294:1995 | Plastics — Injection moulding of test specimens of thermoplastic materials |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 1183:1987 | Plastics — Methods for determining the density and relative density of non-cellular plastics |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 1210:1992 | Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source |
| ISO 2577:2007 | Plastics — Thermosetting moulding materials — Determination of shrinkage |
| ISO 3146:2000 | Plastics — Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods |
| ISO 291:2008 | Plastics — Standard atmospheres for conditioning and testing |
| ISO 62:2008 | Plastics — Determination of water absorption |
| ISO 4589:1984 | Plastics — Determination of flammability by oxygen index |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 179:1993 | Plastics — Determination of Charpy impact strength |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 75-3:2004 | Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics |
| ISO 10724:1994 | Plastics — Thermosetting moulding materials — Injection moulding of multipurpose test specimens |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| IEC 61006:2004 | Electrical insulating materials - Methods of test for the determination of the glass transition temperature |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.