BS 7254-2:1990
Current
The latest, up-to-date edition.
Orthopaedic implants Specification for general requirements for materials and finish
Hardcopy , PDF
English
30-04-1990
Important note : Users cannot be edited or removed once added to your Multi user PDF.NO CONTENTS SECTION
General requirements for orthopaedic implants used for bone surgery including osteosynthesis and joint replacement. Covers metallic and non-metallic implants.
| Committee |
CH/150/5
|
| DevelopmentNote |
Supersedes 88/55737 DC and BS 3531-1(1980). (09/2005) Reviewed and confirmed by BSI, December 2011. (11/2011)
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This Part of BS7254 specifies general requirements for materials and finish of orthopaedic implants used for bone surgery including osteosynthesis and joint replacement, and made of wrought austenitic stainless steel, cast cobalt-based alloys, wrought cobalt-based alloys, wrought titanium, wrought titanium alloy and non-metallic materials.
NOTE1 This Part of BS7254 gives requirements for implants for osteosynthesis and for partial and total joint prostheses. These requirements may be referred to in, or superseded by, Parts of BS3531 and BS7251 as regards particular types of orthopaedic implant. However, it is unlikely that every type of orthopaedic implant will be covered by a Part of BS3531 or BS7251 and, if no individual product specification exists, this Part of BS7254 is intended to give requirements applicable to orthopaedic implants in general.
NOTE2 The titles of the publications referred to in this standard are listed on the inside back cover.
| BS 7251-1:1990 | Orthopaedic joint prostheses Specification for general requirements |
| BS 3531-5.4(1990) : 1990 | IMPLANTS FOR OSTEOSYNTHESIS - BONE SCREWS AND AUXILIARY EQUIPMENT - SPECIFICATION FOR SCREWS HAVING SYMMETRICAL THREAD AND CONICAL UNDER-SURFACES |
| BS 3531-11:1990 | Implants for osteosynthesis Specification for staples |
| BS 3531-6.1:1990 | Implants for osteosynthesis. Skeletal pins and wires Specification for general requirements |
| BS 3531-15:1990 | Implants for osteosynthesis Specification for devices for the fixation of the ends of the femur in adults |
| BS 3531-14.2:1990 | Implants for osteosynthesis. Intramedullary nailing systems Specification for medullary pins (Rush type) and introducer/extractors |
| BS 7254-1:1990 | Orthopaedic implants Specification for marking, packaging and labelling |
| BS 7252-7:1990 | Metallic materials for surgical implants Specification for cobalt-chromium-nickel-molybdenum-iron alloy |
| BS 7253-3:1990 | Non-metallic materials for surgical implants Specification for surgical implants made of heat-vulcanized silicone elastomer |
| BS 7253-4:1990 | Non-metallic materials for surgical implants Specification for ultra-high molecular mass polyethylene in powder form |
| BS 7252-2:1990 | Metallic materials for surgical implants Specification for unalloyed titanium |
| BS 7252-8:1990 | Metallic materials for surgical implants Specification for wrought cobalt-nickel-chromium-molybdenum-tungsten-iron alloy |
| BS 7252-6:1990 | Metallic materials for surgical implants Specification for wrought cobalt-nickel-chromium-molybdenum alloy |
| BS 7253-2:1990 | Non-metallic materials for surgical implants Specification for ceramic materials based on alumina |
| BS 7254-1:1990 | Orthopaedic implants Specification for marking, packaging and labelling |
| BS 7252-3:1990 | Metallic materials for surgical implants Specification for wrought titanium 6-aluminium 4-vanadium alloy |
| BS 7252-5:1990 | Metallic materials for surgical implants Specification for wrought cobalt-chromium-tungsten-nickel alloy |
| BS 7252-4:1990 | Metallic materials for surgical implants Specification for cobalt-chromium-molybdenum casting alloy |
| BS 7252-1:1990 | Metallic materials for surgical implants Specification for wrought stainless steel |
| BS 7253-5:1990 | Non-metallic materials for surgical implants Specification for ultra-high molecular mass polyethylene in moulded form |
| BS 7252-9:1990 | Metallic materials for surgical implants Specification for high-nitrogen stainless steel |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.