BS 7692(1993) : 1993 AMD 9358
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INSULATING POLES (INSULATING STICKS) AND UNIVERSAL TOOL ATTACHMENTS (FITTINGS) FOR LIVE WORKING
15-03-1997
23-11-2012
Committees responsible
National foreword
1 Scope
2 Definitions
2.1 IEV definitions
2.2 Definitions of special terms used in this standard
Chapter I: Insulating poles with permanently attached
fittings
Section one - Technical characteristics
3 General
4 Insulation
5 Dimensional and mechanical characteristics
6 Ends of insulating poles (sticks)
6.1 Mechanical protection
6.2 Corrosion protection
6.3 Conducting parts
7 Multiple tubes or rod tools
Section two - Type tests
8 General
9 Visual inspection
10 Dimensional check
11 Mechanical tests
11.1 Torsion
11.2 Tension
11.3 Compression
11.4 Bending
12 Dye penetration test
13 Electrical test after water conditioning
14 Tie pole (tie stick)
15 Safety hook pole (retractable hook stick)
16 Hook pole extension (retractable hook stick
extension)
17 Universal hand pole (universal hand stick) and
extendable universal hand pole (stick)
18 Wire holding pole (wire holding stick)
19 Cotter-key plier pole
20 Insulated oiler pole (insulated oiler stick)
21 Wire-cutter
22 Measuring pole or rod (stick)
23 Tension puller (dead-end tool)
Section three - Routine tests, quality assurance plan
and acceptance tests
24 Sampling tests
25 Routine tests
Chapter II: Universal tool attachments (fittings)
Section four - Technical characteristics common to all
tool attachments
26 General
27 Dimensional and mechanical characteristics
28 Mechanical protection
29 Corrosion protection
30 Conducting attachments
Section five - Type tests
31 General
32 Visual inspection
33 Dimensional check
34 Compatibility check
35 Hook pole adapter (retractable hook stick adapter)
and universal adapter
36 Formed wire tool
37 Locating pin (locating drift)
38 Conductor cleaning brush: semi-tubular type
39 Conductor cleaning brush: V-shaped type
40 Oilcan
41 Ratchet spanner (ratchet wrench)
42 Spanner (wrench)
43 Split-pin remover (cotter-key installer remover)
44 Holding fork
45 Split-pin installer remover (cotter-key installer
remover)
46 Binding wire-cutter (tie wire-cutter)
47 Rotary blade
48 Rotary prong
49 Adjustable pliers
50 Vice-grip pliers
51 Adjustable insulator fork
52 All-angle pliers
53 Pin-holder
54 Flexible spanner head (flexible wrench head)
55 Ammeter holder
56 Anti-interference braid applicator
57 Hack saw
58 Mirror
59 Conductor (wire) gauge
60 Gap gauge
61 Clevis and tenon pole tools (clevis and tongue
tools)
Section six - Routine tests, quality assurance plan
and acceptance tests
62 Sampling tests
63 Routine tests
Chapter III: Special clauses
64 Marking
65 Modifications
66 Acceptance tests
Appendices
A Acceptance test
B Insulating poles with permanently attached
fittings - Figures
C Universal tool attachments (fittings) - Figures
D Splined ends of poles and attachments - Examples
E Abrasion resistance test - Technical data
ZA Normative references to international publications
with their corresponding European publications
Applies to insulating poles (insulating sticks), and tool attachments (fittings) and is divided into three chapters. Chapter I: specifies the required characteristics for insulating poles with permanently attached fittings and the tests (electrical and mechanical) which shall be satisfied by these tools. Chapter II: specifies the required characteristics for parts which may be attached to and detached from the ends of poles described in Chapter I, and the tests which should be satisfied by these tools. Chapter III: specifies the special clauses applicables to insulating poles and universal tool attachments. AMD 9358 RENUMBERS THIS STANDARD
DevelopmentNote |
Renumbered and superseded by BS EN 60832 Supersedes 88/23761 DC. (12/2005)
|
DocumentType |
Standard
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
IEC 60832:1988 | Identical |
IEC 60212:2010 | Standard conditions for use prior to and during the testing of solid electrical insulating materials |
IEC 60855:1985 | Insulating foam-filled tubes and solid rods for live working |
IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
IEC 60743:2013 | Live working - Terminology for tools, devices and equipment |
IEC 60410:1973 | Sampling plans and procedures for inspection by attributes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.