Skip to content
Please enter a keyword to search

  • BS EN 10113-1:1993

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Hot-rolled products in weldable fine grain structural steels General delivery conditions

    Available format(s):  Hardcopy, PDF

    Superseded date:  17-11-2004

    Language(s):  English

    Published date:  15-09-1993

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Cooperating organizations
    National foreword
    Foreword
    1 Scope
    2 Normative references
    3 Definitions
    4 Information to be supplied by the purchaser
    4.1 General
    4.2 Options
    5 Dimensions, mass and tolerances
    5.1 Dimensions and tolerances
    5.2 Mass of steel
    6 Classification of qualities; designation
    6.1 Classification of qualities
    6.2 Designation
    7 Technical requirements
    7.1 Steel manufacturing process
    7.2 Delivery condition
    7.3 Chemical composition
    7.4 Mechanical properties
    7.5 Technological properties
    7.6 Surface finish
    7.7 Internal defects
    8 Inspection and testing
    8.1 General
    8.2 Sampling
    8.3 Test units
    8.4 Verification of chemical composition
    8.5 Mechanical tests
    8.6 Test methods
    8.7 Retests and resubmission for testing
    8.8 Inspection documents
    9 Marking for flat and long products
    10 Complaints after delivery
    11 Options
    11.1 All products
    11.2 Flat products
    11.3 Long products
    Annex A (normative) Location of samples and test pieces
             (see EURONORM 18)
    Annex B (informative) List of national standards which
             correspond to EURONORMS referenced
    Annex C (informative) List of corresponding former
             designations
    National annex NA (informative) Committees responsible
    National annex NB (informative) Cross-references

    General Product Information - (Show below) - (Hide below)

    Committee ISE/103
    Development Note Together with BS 7613(1994), BS 7668(1994), BS EN 10029, BS EN 10113-2, BS EN 10113-3, BS EN 10155 and BS EN 10210-1 supersedes BS 4360(1990). Supersedes 90/42740 DC. (07/2005)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    EN 10113-2 : 1993 HOT-ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR NORMALIZED/NORMALIZED ROLLED STEELS
    EN 10113-3 : 1993 HOT ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR THERMOMECHANICAL ROLLED STEELS
    BS 2654:1989 Specification for manufacture of vertical steel welded non-refrigerated storage tanks with butt-welded shells for the petroleum industry
    BS 4074:2000 Specification for steel trench struts
    07/30016130 DC : 0 BS 5974 - CODE OF PRACTICE FOR THE PLANNING, DESIGN, SETTING UP AND USE OF TEMPORARILY INSTALLED SUSPENDED ACCESS EQUIPMENT
    BS EN 10113-2:1993 Hot-rolled products in weldable fine grain structural steels Delivery conditions for normalized/normalized rolled steels
    BS 7818:1995 Specification for pedestrian restraint systems in metal
    BS EN 10113-3:1993 Hot-rolled products in weldable fine grain structural steels Delivery conditions for thermomechanical rolled steels
    BS 5975:1996 Code of practice for falsework
    BS 5400-6:1999 STEEL, CONCRETE AND COMPOSITE BRIDGES - PART 6: SPECIFICATION FOR MATERIALS AND WORKMANSHIP, STEEL

    Standards Referencing This Book - (Show below) - (Hide below)

    EURONORM 54 : 1980 HOT-ROLLED SMALL U-BEAMS
    EN 10002-1 : 2001 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
    EURONORM 57 : 1978 HOT-ROLLED ROUND-EDGE UNEQUAL ANGLE STEEL
    EN 10051:2010 Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
    EN 10079:2007 Definition of steel products
    EN 10027-2:2015 DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM
    EURONORM 160 : 1985 ULTRASONIC TESTING OF SHEET STEELS WITH THICKNESSES OF MORE THAN OR EQUAL TO 6mm (REFLECTION TEST)
    EN 10029:2010 Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape
    EURONORM 18 : 1979 TAKING AND PREPARATION OF SAMPLES AND SAMPLE SECTIONS OF STEEL AND STEEL PRODUCTS
    EN 10164:2004 Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
    EURONORM 24 : 1962 NORMAL I-BEAMS, U-BEAMS; PERMISSIBLE DEVIATIONS
    EURONORM 48 : 1984 HOT-ROLLED STRIP STEEL; PERMISSIBLE DEVIATIONS IN DIMENSIONS AND FORM
    EURONORM 53 : 1962 HOT-ROLLED BROAD FLANGED I-BEAMS (WIDE-FLANGED I-BEAMS) WITH PARALLEL FLANGE FACINGS
    EURONORM 103 : 1971 MICROSCOPIC DETERMINATION OF THE FERRITE OR AUSTENITIC GRAIN SIZE OF STEELS
    EURONORM 60 : 1977 HOT-ROLLED ROUND STEEL FOR GENERAL USE
    EURONORM 56 : 1977 HOT-ROLLED ROUND-EDGE EQUAL ANGLE STEEL
    EN 10045-1 : 1990 METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD
    EURONORM 19 : 1957 IPE BEAMS - I-BEAMS WITH PARALLEL FLANGE FACINGS
    EN 10163-2:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats
    EN 10163-1:2004/AC:2007 DELIVERY REQUIREMENTS FOR SURFACE CONDITION OF HOT-ROLLED STEEL PLATES, WIDE FLATS AND SECTIONS - PART 1: GENERAL REQUIREMENTS
    EURONORM 65 : 1980 HOT-ROLLED ROUND STEEL FOR SCREWS AND RIVETS
    EURONORM 67 : 1978 HOT-ROLLED BULB FLATS
    EN 10021:2006 General technical delivery conditions for steel products
    EURONORM 61 : 1982 HOT-ROLLED HEXAGON STEEL
    EURONORM 58 : 1978 HOT-ROLLED FLAT STEEL FOR GENERAL USE
    ISO 2566-1:1984 Steel Conversion of elongation values Part 1: Carbon and low alloy steels
    EURONORM 186 : 1987 ULTRASONIC TESTING OF BROAD FLANGED BEAMS WITH PARALLEL FLANGES AND IPE BEAMS
    EN 10163-3:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections
    EN 10204:2004 Metallic products - Types of inspection documents
    EURONORM 162 : 1981 COLD ROLLED SECTIONS; TECHNICAL TERMS OF DELIVERY
    EN 10027-1:2016 Designation systems for steels - Part 1: Steel names
    EN 10020:2000 Definition and classification of grades of steel
    EURONORM 168 : 1986 IRON AND STEEL PRODUCTS - INSPECTION DOCUMENTS, CONTENTS
    EURONORM 59 : 1978 HOT-ROLLED SQUARE STEEL FOR GENERAL USE
    EURONORM 91 : 1981 HOT-ROLLED WIDE FLATS - PERMISSIBLE DEVIATIONS FOR DIMENSION, FORM AND WEIGHT
    EURONORM 66 : 1967 HOT-ROLLED HALF-ROUND BARS AND FLAT HALF ROUNDS
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective