BS EN 1071-6:2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Advanced technical ceramics. Methods of test for ceramic coatings Determination of the abrasion resistance of coatings by a micro-abrasion wear test
Hardcopy , PDF
31-08-2016
English
31-03-2010
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Significance and use
5 Principle
6 Apparatus and materials
6.1 Test system
6.2 Test balls
6.3 Test slurry
6.4 Measurement of crater dimensions
7 Preparation of test pieces
8 Test procedure
8.1 Different types of test
8.2 Test Type A: No perforation of coating
8.3 Test Type B: Perforation of coating
9 Analysis of results
9.1 Test Type A: no perforation of coating
9.2 Test Type B: perforation of coating
10 Test reproducibility, repeatability and limits
10.1 Reproducibility and repeatability
10.2 Limits
11 Test report
Annex A (normative) - Measurement of coating thickness
Bibliography
Defines a method for measuring the abrasive wear rate of ceramic coatings by means of a micro-scale abrasion wear test, based on the well known crater grinding technique used for film thickness determination.
| Committee |
RPI/13
|
| DevelopmentNote |
Supersedes DD ENV 1071-6 and 05/30136197 DC. (12/2007)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes | |
| UnderRevision |
This part of EN 1071 specifies a method for measuring the abrasive wear rate of ceramic coatings by means of a micro-scale abrasion wear test, based on the well known crater grinding technique used for film thickness determination (see EN 1071-2).
This method can provide data on both film and substrate wear rates, either by performing two separate tests or by careful analysis of data from a single test series.
The test method can be applied to samples with planar or non-planar surfaces but the analysis described in clause 9 applies only to flat samples. For non-planar samples, a more complicated analysis, possibly requiring the use of numerical methods, is required.
| Standards | Relationship |
| NBN EN 1071-6 : 2008 | Identical |
| EN 1071-6:2007 | Identical |
| NS EN 1071-6 : 1ED 2007 | Identical |
| SN EN 1071-6 : 2008 | Identical |
| NF EN 1071-6 : 2007 | Identical |
| NEN EN 1071-6 : 2007 | Identical |
| I.S. EN 1071-6:2008 | Identical |
| DIN EN 1071-6:2008-01 | Identical |
| ISO 3290:2001 | Rolling bearings Balls Dimensions and tolerances |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| EN 1071-1:2003 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 1: Determination of coating thickness by contact probe filometer |
| ASTM A 485 : 2017 : REDLINE | Standard Specification for High Hardenability Antifriction Bearing Steel |
| EN 1071-2:2002 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 2: Determination of coating thickness by the crater grinding method |
| ASTM G 105 : 2016 | Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.