• BS EN 119000 : 1997

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION: DRY AND MERCURY WETTED REED CONTACT UNITS

    Available format(s):  Hardcopy, PDF

    Superseded date:  16-08-2002

    Language(s):  English

    Published date:  01-01-1997

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 General
    1.1 Scope
    1.2 Normative references
    1.3 Units, symbols and terminology
    1.4 Preferred values
    1.5 Marking
    1.6 Subcontracting
    1.7 Order of precedence
    1.8 Precautions regarding mercury
    2 Quality Assessment Procedures
    2.1 General
    2.2 Qualification approval procedures
    2.3 Quality conformance inspection requirements
    3 Test and measurement procedures
    3.1 General
    3.2 Alternative procedures
    3.3 Standard conditions for testing
    3.4 Visual inspection and check of dimensions
    3.5 Functional tests
    3.6 Remanence test
    3.7 Contact circuit resistance
    3.8 Voltage proof
    3.9 Insulation resistance
    3.10 Operate, release, transfer of bridging, and
          bounce times
    3.11 Contact sticking
    3.12 Robustness of terminals
    3.13 Soldering
    3.14 Climatic sequence
    3.15 Damp heat, steady state
    3.16 Rapid change of temperature
    3.17 Salt mist
    3.18 Bump
    3.19 Vibration
    3.20 Shock
    3.21 Acceleration test - Functional test only
    3.22 Sealing
    3.23 Electrical endurance
    3.24 Mechanical endurance
    3.25 Maximum cycling frequency
    3.26 Mounting position test
    3.27 Drain time test
    3.28 Voltage surge test
    Annex A: Standard test coils for reed contact units
    Annex B: Test systems
    Annex C: Example for information sheet on mercury

    Abstract - (Show below) - (Hide below)

    Applicable to dry and mercury wetted reed contact units of assessed quality. Gives tests and measurement procedures for possible selection for use in Detail Specifications for such units. Also defines the quality assessment procedures to be followed. Applicable to reed contact units operated by an applied magnetic field.

    General Product Information - (Show below) - (Hide below)

    Committee EPL/94
    Development Note Supersedes BS CECC17000(1984), BS CECC18000(1984), BS CECC18001(1984), BS CECC19000(1979), BS CECC51000(1986), BS CECC52000(1987) & 94/216359 DC. (08/2005)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    BS EN 60068-2-6 : 2008 ENVIRONMENTAL TESTING - PART 2-6: TESTS - TEST FC: VIBRATION (SINUSOIDAL)
    BS EN 60068-1:2014 (published 2014-03) Environmental testing General and guidance
    BS 2011-2.1T(1981) : 1981 ENVIRONMENTAL TESTING - TESTS - TEST T - SOLDERING
    BS EN 60068-2-27 : 2009 ENVIRONMENTAL TESTING - PART 2-27: TESTS - TEST EA AND GUIDANCE: SHOCK
    BS EN 60068-2-29 : 1993 ENVIRONMENTAL TESTING - TEST METHODS - ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST EB AND GUIDANCE - BUMP
    BS 3939(1970) : LATEST
    BS 5555(1993) : 1993 SPECIFICATION FOR SI UNITS AND RECOMMENDATIONS FOR USE OF THEIR MULTIPLES AND OF CERTAIN OTHER UNITS
    BS CECC 00109:1991 RULE OF PROCEDURE 9 - CERTIFIED TEST RECORDS
    BS 2011-2.1DB(1981) : 1981 ENVIRONMENTAL TESTING - TESTS - TEST DB AND GUIDANCE: DAMP HEAT, CYCLIC (12 + 12 HOUR CYCLE)
    IEC 60027-1:1992 Letters symbols to be used in electrical technology - Part 1: General
    BS 2011-2.1N(1985) : 1985 ENVIRONMENTAL TESTING - TESTS - TEST N: CHANGE OF TEMPERATURE
    BS 2011-2.1U(1984) : 1984 ENVIRONMENTAL TESTING - TESTS - TEST U: ROBUSTNESS OF TERMINATION AND INTEGRAL MOUNTING DEVICES
    BS 2011-2.1CA(1977) : 1977 ENVIRONMENTAL TESTING - TESTS - TEST CA - DAMP HEAT, STEADY STATE
    IEC 60410:1973 Sampling plans and procedures for inspection by attributes
    BS EN 60068-2-1:2007 (published 2007-05) Environmental testing Tests. Test A. Cold
    BS EN 60068-2-7 : 1993 ENVIRONMENTAL TESTING - TEST METHODS - TEST GA AND GUIDANCE - ACCELERATION, STEADY STATE
    BS CECC00114-2(1995) : 1995 RULE OF PROCEDURE 14 - QUALITY ASSESSMENT PROCEDURES - QUALIFICATION APPROVAL OF ELECTRONIC COMPONENTS
    IEC 60317-1:2010 Specifications for particular types of winding wires - Part 1: Polyvinyl acetal enamelled round copper wire, class 105
    BS EN 60068-2-17 : 1995 ENVIRONMENTAL TESTING - TEST METHODS - TEST Q - SEALING
    BS EN 60068-2-2:2007 (published 2007-10) Environmental testing Tests. Test B. Dry heat
    BS 2011-2.1M(1984) : 1984 ENVIRONMENTAL TESTING - TESTS - TEST M: LOW AIR PRESSURE
    BS 2011-2.1KA(1982) : 1982 BASIC ENVIRONMENTAL TESTING PROCEDURES - PART 2.1: TESTS - TEST KA: SALT MIST
    EN 60317-1 : 1994 AMD 2 1998 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 1: POLYVINYL ACETAL ENAMELLED ROUND COPPER WIRE, CLASS 105
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective