• There are no items in your cart

BS EN 133200:1999

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Harmonized system of quality assessment for electronic components. Sectional specification:passive filter units for electromagnetic interference suppression (filters for which safety tests are required)

Available format(s)

Hardcopy , PDF

Superseded date

19-08-2005

Language(s)

English

Published date

15-10-1999

Foreword
1. GENERAL
1.1 Scope
1.2 Related documents
1.3 Information to be given in a detail specification
1.4 Terminology
1.5 Marking
2. PREFERRED RATINGS AND CHARACTERISTICS
2.1 Preferred characteristics
2.2 Preferred values of ratings
3. QUALITY ASSESSMENT PROCEDURES
3.1 Primary stage of manufacture
3.2 Structurally similar filters
3.3 Certified records of released lots
3.4 Approval testing
3.5 Quality conformance inspection
4. TEST AND MEASUREMENT PROCEDURES
4.0 Capacitance and tan delta measurements
4.1 Visual examination and check of dimensions
4.2 Voltage proof
4.3 Insulation resistance
4.4 D.c. line resistance or voltage drop at rated current
4.5 Insertion loss
4.6 Resistance
4.7 Robustness of terminations
4.8 Resistance to soldering heat
4.9 Solderability
4.10 Rapid change of temperature
4.11 Vibration
4.12 Bump
4.13 Shock
4.14 Container sealing
4.15 Climatic sequence
4.16 Damp heat, steady state
4.17 Temperature rise
4.18 Impulse voltage
4.19 Endurance
4.20 Charge and discharge
4.21 Passive flammability
4.22 Current overload
4.23 Solvent resistance of the marking
4.24 Component solvent resistance
Annex A Test schedule for qualification approval
Annex B Test schedule for safety requirements only
Annex C Circuit for the impulse voltage test
Annex D Suitable circuit for the endurance test
Annex E Declaration of design (normative)

Defines passive filter units for electromagnetic interference suppression which fall within the scope of the Generic Specification EN 133000. Specified according to this specification will either be connected to mains supplies, when compliance with the mandatory tests of Table 2 is necessary, or used on other circuit positions where the equipment specification prescribes that some or all of these safety tests are required. Applies to those connected to an a.c. mains or other supply with a nominal voltage not exceeding 1000 V a.c. (r.m.s.) or 1000 V d.c. with a nominal frequency not exceeding 400 Hz.

Committee
W/-
DevelopmentNote
Supersedes 91/34179 DC. (03/2007)
DocumentType
Standard
Pages
44
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
I.S. EN 133200:1995 Identical
SN EN 133200 : 1994 Identical
DIN EN 133200 : 2000 Identical
EN 133200:1999 Identical

EN 60998-2-2:2004 Connecting devices for low-voltage circuits for household and similar purposes - Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units
EN 133100:1998 Sectional Specification: Passive filter units for electromagnetic interference suppression - Filters for which safety tests are not required
IEC 60384-14:2013+AMD1:2016 CSV Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
IEC 61210:2010 Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements
ISO 3:1973 Preferred numbers Series of preferred numbers
EN 133221:1998 Blank Detail Specification: Passive filter units for electromagnetic interference suppression - Filters for which safety tests are required (safety tests only)
IEC 60085:2007 Electrical insulation - Thermal evaluation and designation
EN 132400 : 1994 AMD 4 2001 SECTIONAL SPECIFICATION: FIXED CAPACITORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION AND CONNECTION TO THE SUPPLY MAINS (ASSESSMENT LEVEL D)
IEC 60410:1973 Sampling plans and procedures for inspection by attributes
IEC 60294:2012 Measurement of the dimensions of a cylindrical component with axial terminations
IEC 60940:2015 Guidance information on the application of capacitors, resistors, inductors and complete filter units for electromagnetic interference suppression
EN 133201:1998 Blank Detail Specification: Passive filter units for electromagnetic interference suppression - Filters for which safety tests are required
IEC 60062:2016 Marking codes for resistors and capacitors
IEC 60063:2015 Preferred number series for resistors and capacitors
EN 133000:1997 Generic Specification: Passive filter units for electromagnetic interference suppression
IEC 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements

€271.12
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.