• BS EN 13980:2002

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Potentially explosive atmospheres. Application of quality systems

    Available format(s):  Hardcopy, PDF

    Superseded date:  30-09-2011

    Language(s):  English

    Published date:  05-12-2002

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Quality management system
      4.1 General requirements
      4.2 Documentation requirements
          4.2.1 General
          4.2.2 Quality manual
          4.2.3 Control of documents
          4.2.4 Control of quality records
    5 Management responsibility
      5.1 Management commitment
      5.2 Customer focus
      5.3 Quality policy
      5.4 Planning
          5.4.1 Quality objectives
          5.4.2 Quality management system planning
      5.5 Responsibility, authority and communication
          5.5.1 Responsibility and authority
          5.5.2 Management representative
          5.5.3 Internal communication
      5.6 Management review
          5.6.1 General
          5.6.2 Review input
          5.6.3 Review output
    6 Resource management
      6.1 Provision of resources
      6.2 Human resources
          6.2.1 General
          6.2.2 Competence, awareness and training
      6.3 Infrastructure
      6.4 Work environment
    7 Product realisation
      7.1 Planning of product realisation
      7.2 Customer-related processes
          7.2.1 Determination of requirements related to the
                product
          7.2.2 Review of requirements related to the product
          7.2.3 Customer communication
      7.3 Design and development
      7.4 Purchasing
          7.4.1 Purchasing process
          7.4.2 Purchasing information
          7.4.3 Verification of purchased product
      7.5 Production and service provision
          7.5.1 Control of production and service provision
          7.5.2 Validation of processes for production and
                service provision
          7.5.3 Identification and traceability
          7.5.4 Customer property
          7.5.5 Preservation of product
      7.6 Control of monitoring and measuring devices
    8 Measurement, analysis and improvement
      8.1 General
      8.2 Monitoring and measurement
          8.2.1 Customer satisfaction
          8.2.2 Internal audit
          8.2.3 Monitoring and measurement of processes
          8.2.4 Monitoring and measurement of product
      8.3 Control of non-conforming product
      8.4 Analysis of date
          8.5 Improvement
          8.5.1 Continual improvement
          8.5.2 Corrective action
          8.5.3 Preventive action
    Annex A (informative) Information relevant to particular
            types pf protection
    Annex B (informative) Verification criteria for sintered
            components used as an integral part of a type of
            protection
    Annex ZA (informative) Clauses of this European standard
             addressing essential requirements or other provisions
             of EU Directives
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes particular requirements and information for establishing and maintaining a quality system in accordance with the requirements of Annex IV and Annex VII of Directive 94/9/EC.

    General Product Information - (Show below) - (Hide below)

    Committee EXL/23
    Development Note Supersedes 00/541127 DC (12/2002)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
    ISO/IEC Guide 62:1996 General requirements for bodies operating assessment and certification/registration of quality systems
    ISO 2738:1999 Sintered metal materials, excluding hardmetals — Permeable sintered metal materials — Determination of density, oil content and open porosity
    EN 45014 : 1998 GENERAL CRITERIA FOR SUPPLIER'S DECLARATION OF CONFORMITY
    PREN 13237-1 : DRAFT 1998 POTENTIALLY EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: TERMS AND DEFINITIONS FOR EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
    ISO 4003:1977 Permeable sintered metal materials — Determination of bubble test pore size
    EN 45011:1998 General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996)
    EN 45011 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS
    EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
    ISO 9001:2015 Quality management systems — Requirements
    ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
    ISO/IEC Guide 65:1996 General requirements for bodies operating product certification systems
    EN 45012 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS
    EN ISO 9000:2015 Quality management systems - Fundamentals and vocabulary (ISO 9000:2015)
    1994/9/EC : 1994 DIRECTIVE 94/9/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 23 MARCH 1994 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
    EN 45001 : 1989 GENERAL CRITERIA FOR THE OPERATION OF TESTING LABORATORIES
    ISO/IEC Guide 22:1996 General criteria for supplier's declaration of conformity
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective