• BS EN 186000-1 : 1994

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION - CONNECTOR SETS FOR OPTICAL FIBRES AND CABLES - PART 1: REQUIREMENTS, TEST METHODS AND QUALIFICATION APPROVAL PROCEDURES

    Available format(s):  Hardcopy, PDF

    Superseded date:  28-02-2007

    Language(s):  English

    Published date:  01-01-1994

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Cooperating organizations
    National foreword
    Foreword
    Preface
    CECC specification system
    Section one - General
    1 General
    1.1 Scope
    1.2 Related documents
    1.3 Definitions
    Section two - Requirements
    2 Requirements
    2.1 Classification
    2.1.1 Type
    2.1.2 Arrangement
    2.1.3 Style
    2.1.4 Variant
    2.1.5 Climatic category
    2.1.6 Environmental category
    2.1.7 Assessment level
    2.2 Documentation
    2.2.1 Symbols
    2.2.2 Specification system
              Sectional specifications
              Blank detail specifications
              Detail specifications
    2.2.3 Drawings
              Projection system
              Dimensional system
              Intermateability (in preparation)
    2.2.4 Measurements
              Measurement method
              Reference components
              Gauges
    2.2.5 Test data sheets
    2.2.6 Instructions for use
    2.3 Design and construction
    2.3.1 Materials
              Corrosion resistance
              Non-flammable materials
    2.3.2 Workmanship
    2.4 Quality
    2.5 Performance
    2.6 Identification and marking
    2.6.1 Variant identification number
    2.6.2 Component marking
    2.6.3 Package marking
    2.7 Packaging
    Section three - Quality assessment procedures
    3 Quality assessment procedures
    3.1 Primary stage of manufacture
    3.2 Structural similarity
    3.3 Qualification approval procedures
    3.3.1 Fixed sample procedure
    3.3.2 Lot-by-lot and periodic pressure
    3.3.3 Qualifying specimen
    3.3.4 Counterpart component
    3.3.5 Sample size
    3.3.6 Qualification testing
    3.3.7 Qualification failures
    3.3.8 Maintenance of qualification approval
    3.3.9 Qualification report
    3.4 Quality conformance inspection
    3.4.1 Lot-by-lot inspection
              Formation of inspection lots
              Rejected lots
    3.4.2 Periodic inspection
              Sample size
              Preparation of specimens
              Periodic inspection
              Periodic inspection failures
              Periodic inspection report
    3.5 Certified test records of released lots
    3.6 Delayed deliveries
    3.7 Delivery release before completion of group B
            tests
    3.8 Alternative test methods
    3.9 Unchecked parameters
    Section four - Measurement and environmental test
                    procedures
    4 Measurement and environmental test procedures
    4.1 Standard conditions
    4.2 Specimen
    4.3 Cleaning of optical surfaces
    4.4 Measurement procedures
    4.4.1 Visual inspection
    4.4.2 Dimensions
    4.4.3 Examination of product
    4.4.4 Gauge retention force
    4.4.5 Engagement and separation forces
    4.4.6 Flammability (fire hazard)
    4.4.7 Insertion loss
    4.4.8 Change in transmitted optical power
    4.4.9 Cross talk
    4.4.10 Ambient light coupling
    4.4.11 Spectral loss
    4.4.12 Return loss
    4.5 Environmental test procedures
    4.5.1 Vibration (sinusoidal)
    4.5.2 Effectiveness of fibre of ferrule retention
    4.5.3 Static load
    4.5.4 Cable pulling
    4.5.5 Cable torsion
    4.5.6 Strength of coupling mechanism
    4.5.7 Bending moment
    4.5.8 Bump
    4.5.9 Shock
    4.5.10 Crush resistance
    4.5.11 Axial compression
    4.5.12 Impact
    4.5.13 Acceleration
    4.5.14 Drop
    4.5.15 Coupling proof torque
    4.5.16 Mould growth
    4.5.17 Cold
    4.5.18 Dry heat
    4.5.19 Damp heat (steady state)
    4.5.20 Climatic sequence
    4.5.21 Condensation
    4.5.22 Change of temperature
    4.5.23 Sealing (panel-sealed and barrier sealed
            connectors)
    4.5.24 Sealing (water immersion)
    4.5.25 Sealing (hermetic)
    4.5.26 Salt mist
    4.5.27 Dust
    4.5.28 Industrial atmosphere (sulphur dioxide)
    4.5.29 Low air pressure
    4.5.30 Solar radiation
    4.5.31 Nuclear radiation
    4.5.32 Mechanical endurance
    4.5.33 High temperature endurance
    4.5.34 Resistance to solvents and contaminating fluids
    4.5.35 Cable nutation
    Annexes (informative)
    A Size measurements
    B Summary of definitions from IEC publications
    Part II: Capability approval procedure (in preparation)
    National annex NA (informative) Committees responsible
    National annex NB (informative) Cross-references

    Abstract - (Show below) - (Hide below)

    Applies to fibre optic connector sets for optical fibres and cables. Coverage includes definitions, environmental category, gauges, corrosion resistance, component marking, package marking, spectral loss, cable torsion, cable pulling, static load, nuclear radiation, solar radiation, spectral loss, axial compression and industrial atmosphere.

    General Product Information - (Show below) - (Hide below)

    Committee GEL/86
    Development Note Supersedes BS 9230(1986) (09/2005)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS EN 186180 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - SECTIONAL SPECIFICATION - CONNECTOR SETS FOR OPTICAL FIBRES AND CABLES - TYPE LSB
    BS EN 186240 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - SECTIONAL SPECIFICATION: CONNECTOR SETS FOR OPTICAL FIBRES AND CABLES - TYPE MT
    BS EN 186130 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - SECTIONAL SPECIFICATION - CONNECTOR SETS FOR OPTICAL FIBRES AND CABLES - TYPE LSA
    BS EN 186220 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - SECTIONAL SPECIFICATION: CONNECTOR SETS FOR OPTICAL FIBRES AND CABLES - TYPE LSC
    BS EN 186230 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - SECTIONAL SPECIFICATION: CONNECTOR SETS FOR OPTICAL FIBRES AND CABLES - TYPE LSF
    BS EN 186210 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - SECTIONAL SPECIFICATION: CONNECTOR SETS FOR OPTICAL FIBRES AND CABLES - TYPE CF08
    BS EN 186006-1 : 1996 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - BLANK DETAIL SPECIFICATION - CONNECTORS FOR OPTICAL FIBRES AND CABLES FOR MILITARY USE - ENVIRONMENTAL CATEGORY 6
    BS EN 186110 : 1995 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - SECTIONAL SPECIFICATION: CONNECTOR SETS FOR OPTICAL FIBRES AND CABLES - TYPE FC
    BS EN 186100 : 1995 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - SECTIONAL SPECIFICATION: CONNECTOR SETS FOR OPTICAL FIBRES AND CABLES - TYPES F- SMA

    Standards Referencing This Book - (Show below) - (Hide below)

    BS 2011-2.1J(1989) : 1989 ENVIRONMENTAL TESTING - TESTS - TEST J AND GUIDANCE - MOULD GROWTH
    BS 2011-2.1B(1977) : 1977 ENVIRONMENTAL TESTING - TESTS - TEST B. DRY HEAT
    ISO 1101:2017 Geometrical product specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out
    BS 2011-2.1DB(1981) : 1981 ENVIRONMENTAL TESTING - TESTS - TEST DB AND GUIDANCE: DAMP HEAT, CYCLIC (12 + 12 HOUR CYCLE)
    IEC 60793-1:1992 Optical fibres - Part 1: Generic specification
    IEC 60068-2-11:1981 ENVIRONMENTAL TESTING - TEST KA: SALT MIST
    BS 2011-2.2SA(1977) : 1977 ENVIRONMENTAL TESTING - GUIDANCE - TEST Sa. GUIDANCE FOR SOLAR RADIATION TESTING
    BS 2011-2.1N(1985) : 1985 ENVIRONMENTAL TESTING - TESTS - TEST N: CHANGE OF TEMPERATURE
    BS 2011-2.1A(1990) : 1990 AMD 7783 ENVIRONMENTAL TESTING - TESTS - TEST A: COLD
    BS 2011-2.1CA(1977) : 1977 ENVIRONMENTAL TESTING - TESTS - TEST CA - DAMP HEAT, STEADY STATE
    IEC 60410:1973 Sampling plans and procedures for inspection by attributes
    BS 2011-2.1EA(1988) : 1988 AMD 7814 ENVIRONMENTAL TESTING - TEST - TEST EA: SHOCK
    BS 2011-2.1SA(1977) : 1977 ENVIRONMENTAL TESTING - TESTS - TEST Sa. SIMULATED SOLAR RADIATION AT GROUND LEVEL
    CECC 00114-2 : 1994 RULE OF PROCEDURE 14 - QUALITY ASSESSMENT PROCEDURES - PART 2: QUALIFICATION APPROVAL OF ELECTRONIC COMPONENTS
    BS 2011-2.1EB(1987) : 1987 AMD 7827 ENVIRONMENTAL TESTING - TEST - TEST EB: BUMP
    BS 2011-2.1FC(1983) : 1983 ENVIRONMENTAL TESTING - TESTS - TEST FC: VIBRATION (SINUSOIDAL)
    BS 2011-1.1(1989) : 1989 ENVIRONMENTAL TESTING - GENERAL AND GUIDANCE
    ISO 2015:1976 Numbering of weeks
    BS 2011-2.1M(1984) : 1984 ENVIRONMENTAL TESTING - TESTS - TEST M: LOW AIR PRESSURE
    BS 2011-2.1Q(1981) : 1981 ENVIRONMENTAL TESTING - TESTS - TEST Q: SEALING
    BS 2011-2.1GA(1984) : 1984 ENVIRONMENTAL TESTING - TESTS - TEST GA: ACCELERATION STEADY STATE
    ISO 129:1985 Technical drawings — Dimensioning — General principles, definitions, methods of execution and special indications
    BS 308-2(1985) : 1985 ENGINEERING DRAWING PRACTICE - RECOMMENDATIONS FOR DIMENSIONING AND TOLERANCING OF SIZE
    IEC 60875-1:2015 Fibre optic interconnecting devices and passive components - Non-wavelength-selective fibre optic branching devices - Part 1: Generic specification
    ISO/R 286:1962 ISO system of limits and fits Part I : General, tolerances and deviations
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective