• BS EN 196000 : 1993

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - GENERIC SPECIFICATION - ELECTROMECHANICAL SWITCHES

    Available format(s):  Hardcopy, PDF

    Superseded date:  28-02-2010

    Language(s):  English

    Published date:  01-01-1993

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Cooperating organizations
    National foreword
    Foreword
    Preface
    Section one - Scope
    1.1 Scope
    1.2 Switch classes included
    1.3 Switch classes excluded
    Section two - General
    2.1 Normative references
    2.2 Units, symbols and terminology
    2.3 Standard and preferred values
    2.4 Marking
    2.5 Safety requirements
    Section three - Quality assessment procedure
    3.1 Primary stage of manufacture
    3.2 Structural similarity
    3.3 Qualification approval procedure
    3.4 Quality conformance inspection
    3.5 Certified test records
    3.6 Delayed delivery
    3.7 Re-submission of rejected lots
    3.8 Alternative test methods
    3.9 Release for delivery before the completion of
            group B tests
    3.10 Capability approval
    3.11 Rework
    Section four - Test and measurement procedures
    4.1 Standard conditions for testing
    4.2 Optional reduction of testing
    4.3 Individual test methods
    4.3.1 General examination
    4.3.2 Electrical continuity and contact resistance
    4.3.3 Insulation
    4.3.4 Voltage stress
    4.3.5 Current carrying capacity
    4.3.6 Dynamic stress
    4.3.7 Impact stress
    4.3.8 Mechanical strength
    4.3.9 Endurance
    4.3.10 Overload
    4.3.11 Climatic
    4.3.12 Soldering
    4.3.13 Mechanical operating characteristics
    4.3.14 Sealing
    4.3.15 Chemical resistance
    4.3.16 Fire hazard
    4.3.17 Capacitance
    4.3.18 Illumination
    4.3.19 Temperature response
    Annex
    A Test schedules for quality conformance
            inspection and qualification approval
    National annex NA (informative) Committees responsible
    National annex NB (informative) Cross-references

    Abstract - (Show below) - (Hide below)

    Relates to electromechanical switches meant primarily for use in telecommunications equipment and in electronic equipment employing techniques. Limited to switches with a maximum 500 v (d.c. or a.c. r.m.s) rated voltage and a maximum 25 A rated carrying current. Specifies the definitions, terms, test methods and other material necessary to prepare detail specifications for those components in the CECC System.

    General Product Information - (Show below) - (Hide below)

    Committee EPL/48
    Development Note Supersedes 90/24478 DC. Supersedes BS CECC96000(1987) which remains current. (05/2002)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    EN 196500:1993/A1:2001 SECTIONAL SPECIFICATION: MEMBRANE SWITCHES INCLUDING BLANK DETAIL SPECIFICATION EN 196501
    BS EN 196500 : 1993 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - SECTIONAL SPECIFICATION: MEMBRANE SWITCHES INCLUDING BLANK DETAIL SPECIFICATION EN 196501

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60068-2-5:2010 Environmental testing - Part 2-5: Tests - Test Sa: Simulated solar radiation at ground level and guidance for solar radiation testing
    CECC 00109 : 1974 CECC RULES OF PROCEDURE: RP 9: CERTIFIED TESTS RECORDS
    IEC 60512-8:1993 Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 8: Connector tests (mechanical) and mechanical tests on contacts and terminations
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    IEC 60695-2-1:1991 Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance
    IEC 61020-1:2009 Electromechanical switches for use in electrical and electronic equipment - Part 1: Generic specification
    IEC 60512-6:1984 Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 6: Climatic tests and soldering tests
    IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
    IEC 60341-1:1970 Push-button switches - Part 1: General requirements and measuring methods
    IEC 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
    IEC 60068-2-13:1983 Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure
    IEC 60512-7:1993 Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 7: Mechanical operating tests and sealing tests
    CECC 00114 : 93 AMD 1 QUALITY ASSESSMENT PROCEDURES - APPROVAL OF MANUFACTURERS AND OTHER ORGANIZATIONS
    IEC 60410:1973 Sampling plans and procedures for inspection by attributes
    IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
    IEC 60512-4:1976 Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 4: Dynamic stress tests
    CECC 00111 : 80 AMD 3 CECC RULES OF PROCEDURE: RP 11: SPECIFICATIONS AND THEIR HARMONIZATION - COMPONENTS FOR GENERAL AND PROFESSIONAL USAGE - COMPONENTS OF ENHANCED ASSESSMENT OF QUALITY
    IEC 60512-9:1992 Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 9: Miscellaneous tests
    CECC 00009 : 1980 BASIC SPECIFICATION: BASIC TESTING PROCEDURES AND MEASURING METHODS FOR ELECTROMECHANICAL COMPONENTS
    IEC 60068-2-29:1987 Environmental testing. Part 2: Tests. Test Eb and guidance: Bump
    IEC 60512-5:1992 Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 5: Impact tests (free components), static load tests (fixed components), endurance tests and overload tests
    IEC 60512-1:2001 Connectors for electronic equipment - Tests and measurements - Part 1: General
    CECC 00007 : 1978 BASIC SPECIFICATION: SAMPLING PLANS AND PROCEDURES FOR INSPECTION BY ATTRIBUTES
    IEC 60050-581:2008 International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
    IEC 60512-3:1976 Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 3: Current-carrying capacity tests
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective