• BS EN 50131-2-4:2008

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Alarm systems. Intrusion and hold-up systems Requirements for combined passive infrared and microwave detectors

    Available format(s):  Hardcopy, PDF

    Superseded date:  13-08-2020

    Language(s):  English

    Published date:  31-05-2014

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Introduction
    1 Scope
    2 Normative references
    3 Definitions and abbreviations
    4 Functional requirements
    5 Marking, identification and documentation
    6 Testing
    Annexes
    Annex A (normative) - Dimensions & Requirements
            of the standardised Test Magnets
    Annex B (normative) - General testing matrix
    Annex C (normative) - Walk test diagrams
    Annex D (normative) - Procedure for calculation of
            the average temperature difference between the
            standard target and the background
    Annex E (informative) - Basic detection target for the
            basic test of detection capability
    Annex F (informative) - Equipment for walk test
            velocity control
    Annex G (informative) - Immunity to visible and near
            Infrared radiation - Notes on calibration of the
            light source
    Annex H (informative) - Immunity to microwave signal
            interference by fluorescent lights
    Annex I (informative) - Example list of small tools
    Annex J (informative) - Test for resistance to re-orientation
            of adjustable mountings
    National Annex NA (Informative) - Text of IS1 to
                      EN 50131-2-4:2008

    Abstract - (Show below) - (Hide below)

    Details combined passive infrared and microwave detectors installed in buildings and provides for security Grades 1 to 4, specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV.

    Scope - (Show below) - (Hide below)

    This standard is for combined passive infrared and microwave detectors installed in buildings and provides for security Grades 1 to 4 (see EN 50131-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see EN 50130-5). This standard does not include requirements for detectors intended for use outdoors.

    A detector shall fulfil all the requirements of the specified grade.

    Functions additional to the mandatory functions specified in this standard may be included in the detector, providing they do not influence the correct operation of the mandatory functions.

    This European Standard does not apply to system interconnections.

    General Product Information - (Show below) - (Hide below)

    Committee GW/1/1
    Development Note Supersedes DD CLC/TS 50131-2-4 & 07/30162640 DC. (02/2008)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes
    Under Revision

    Standards Referenced By This Book - (Show below) - (Hide below)

    PD 6662:2010 Scheme for the application of European standards for intrusion and hold-up alarm systems
    PD 6662:2017 Scheme for the application of European Standards for intrusion and hold-up alarm systems
    09/30203716 DC : 0 PD 6662 - SCHEME FOR THE APPLICATION OF EUROPEAN STANDARDS FOR INTRUSION AND HOLD-UP ALARM SYSTEMS

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    IEC 60404-8-1:2015 Magnetic materials - Part 8-1: Specifications for individual materials - Magnetically hard materials
    EN 60068-1:2014 Environmental testing - Part 1: General and guidance
    IEC 60404-14:2002 Magnetic materials - Part 14: Methods of measurement of the magnetic dipole moment of a ferromagnetic material specimen by the withdrawal or rotation method
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 60404-5:2015 RLV Magnetic materials - Part 5: Permanent magnet (magnetically hard) materials - Methods of measurement of magnetic properties
    EN 50131-1:2006/A2:2017 ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 1: SYSTEM REQUIREMENTS
    EN 50131-6:2017 Alarm systems - Intrusion and hold-up systems - Part 6: Power supplies
    EN 60404-5:2015 Magnetic materials - Part 5: Permanent magnet (magnetically hard) materials - Methods of measurement of magnetic properties
    EN 50130-4:2011/A1:2014 ALARM SYSTEMS - PART 4: ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD: IMMUNITY REQUIREMENTS FOR COMPONENTS OF FIRE, INTRUDER, HOLD UP, CCTV, ACCESS CONTROL AND SOCIAL ALARM SYSTEMS
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    EN 60404-14:2002 Magnetic materials - Part 14: Methods of measurement of the magnetic dipole moment of a ferromagnetic material specimen by the withdrawal or rotation method
    IEC 60068-2-52:2017 Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution)
    EN 50130-5:2011 ALARM SYSTEMS - PART 5: ENVIRONMENTAL TEST METHODS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective