• BS EN 55011 : 2016

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    INDUSTRIAL, SCIENTIFIC AND MEDICAL EQUIPMENT - RADIO-FREQUENCY DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT

    Available format(s):  Hardcopy, PDF

    Superseded date:  02-04-2020

    Language(s):  English

    Published date:  01-01-2016

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 National measures and frequencies designated
       for ISM use
    5 Classification of equipment
    6 Limits of electromagnetic disturbances
    7 Measurement requirements
    8 Special provisions for test site measurements
       (9 kHz to 1 GHz)
    9 Radiation measurements: 1 GHz to 18 GHz
    10 Measurement in situ
    11 Safety precautions for emission measurements
       on ISM RF equipment
    12 Measurement uncertainty
    Annex A (informative) - Examples of equipment classification
    Annex B (informative) - Precautions to be taken in the use of
            a spectrum analyzer
    Annex C (normative) - Measurement of electromagnetic
            radiation disturbance in the presence of signals from
            radio transmitters
    Annex D (informative) - Propagation of interference from
            industrial radio-frequency equipment at frequencies
            between 30 MHz and 300 MHz
    Annex E (informative) - Recommendations of CISPR
            for protection of certain radio services in particular
            areas
    Annex F (informative) - Frequency bands allocated for
            safety-related radio services
    Annex G (informative) - Frequency bands allocated for
            sensitive radio services
    Annex H (informative) - Statistical assessment of series
            produced equipment against the requirements of
            CISPR standards
    Annex I (normative) - Artificial Network (AN) for the
            assessment of disturbance voltages at d.c. power
            ports of semiconductor power converters
    Annex J (informative) - Measurements on Grid Connected
            Power Converters (GCPC) - Setups for an effective test
            site configuration
    Annex K (informative) - Test site configuration and
            instrumentation - Guidance on prevention of saturation
            effects in mitigation filters of transformer-less power
            converters during type tests according to this standard
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications
    Annex ZB (normative) - Frequencies designated on
             a national basis in CENELEC countries for use
             as fundamental ISM frequencies
    Annex ZZ (informative) - Coverage of Essential
             Requirements of EU Directives

    Abstract - (Show below) - (Hide below)

    Pertains to industrial, scientific and medical electrical equipment operating in the frequency range 0 Hz to 400 GHz and to domestic and similar appliances designed to generate and/or use locally radio-frequency energy.

    General Product Information - (Show below) - (Hide below)

    Committee GEL/210/11
    Development Note Supersedes 94/209651 DC.(07/2002) Supersedes 00/240716 DC and 00/244622 DC.(08/2003) Supersedes 04/30113595 DC.(05/2007) Supersedes 00/247663 DC. (09/2007) Supersedes 05/30142150 DC.(01/2010) Supersedes 08/30181131 DC.(08/2010) 2009 + A1 2010 Edition remains active & will be withdrawn on 15/02/2019. Supersedes 11/30257479 DC, 12/30263968 DC & 12/30263969 DC.(05/2016) 2016 Edition Re-issued in July 2017 & incorporates AMD 1 2017. (08/2017) 2016 Edition remains current and will be withdrawn on 21/04/2020.(11/2017)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    08/30136724 DC : DRAFT MAY 2008 BS 6739 - CODE OF PRACTICE FOR INSTRUMENTATION IN PROCESS CONTROL SYSTEMS - INSTALLATION DESIGN AND PRACTICE

    Standards Referencing This Book - (Show below) - (Hide below)

    CISPR 14-1:2016 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission
    EN 62135-2:2015 RESISTANCE WELDING EQUIPMENT - PART 2: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS (IEC 62135-2:2015)
    CISPR 16-4-2:2011+AMD1:2014 CSV Specification for radio disturbance and immunity measuring apparatusand methods - Part 4-2: Uncertainties, statistics and limit modelling - Measurement instrumentation uncertainty
    EN 55016-2-3:2017 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 2-3: METHODS OF MEASUREMENT OF DISTURBANCES AND IMMUNITY - RADIATED DISTURBANCE MEASUREMENTS
    EN 55016-1-4:2010/A2:2017 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-4: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - ANTENNAS AND TEST SITES FOR RADIATED DISTURBANCE MEASUREMENTS (CISPR 16-1-4:2010/A2:2017)
    CISPR 16-1-4:2010+AMD1:2012+AMD2:2017 CSV Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements
    CISPR 16-1-1:2015 Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus
    IEC TR 60083:2015 Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC
    IEC 60364-5-51:2005 Electrical installations of buildings - Part 5-51: Selection and erection of electrical equipment - Common rules
    CISPR 16-2-1:2014 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-1: Methods of measurement of disturbances and immunity - Conducted disturbance measurements
    CISPR 15:2013+AMD1:2015 CSV Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment
    IEC 60974-10:2014+AMD1:2015 CSV Arc welding equipment - Part 10: Electromagnetic compatibility (EMC)requirements
    2004/108/EC : 2004 DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 DECEMBER 2004 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO ELECTROMAGNETIC COMPATIBILITY AND REPEALING DIRECTIVE 89/336/EC
    CISPR TR 16-4-3:2004+AMD1:2006 CSV Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-3: Uncertainties, statistics and limit modelling - Statistical considerations in the determination of EMC compliance of mass-produced products
    IEC TR 61000-2-5:2017 Electromagnetic compatibility (EMC) - Part 2-5: Environment - Description and classification of electromagnetic environments
    IEC 60364-1:2005 Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
    IEC 60601-1-2:2014 Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral Standard: Electromagnetic disturbances - Requirements and tests
    EN 60601-1-2:2015 MEDICAL ELECTRICAL EQUIPMENT - PART 1-2: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE - COLLATERAL STANDARD: ELECTROMAGNETIC DISTURBANCES - REQUIREMENTS AND TESTS (IEC 60601-1-2:2014)
    IEC 60601-2-2:2017 Medical electrical equipment - Part 2-2: Particular requirements for the basic safety and essential performance of high frequency surgical equipment and high frequency surgical accessories
    EN 61307:2011 INDUSTRIAL MICROWAVE HEATING INSTALLATIONS - TEST METHODS FOR THE DETERMINATION OF POWER OUTPUT
    CISPR TR 16-2-5:2008 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-5: In situ measurements for disturbing emissions produced by physically large equipment
    IEC 62135-2:2015 Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements
    CISPR 16-2-3:2016 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements
    CISPR TR 16-4-4:2007 Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-4: Uncertainties, statistics and limit modelling - Statistics of complaints and a model for the calculation of limits for the protection of radio services
    EN 60974-10:2014/A1:2015 ARC WELDING EQUIPMENT - PART 10: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS (IEC 60974-10:2014/A1:2015)
    IEC 61307:2011 Industrial microwave heating installations - Test methods for the determination of power output
    EN 55016-2-1:2014/A1:2017 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 2-1: METHODS OF MEASUREMENT OF DISTURBANCES AND IMMUNITY - CONDUCTED DISTURBANCE MEASUREMENTS (CISPR 16-2-1:2014/A1:2017)
    IEC 60705:2010+AMD1:2014 CSV Household microwave ovens - Methods for measuring performance
    EN 55016-1-1:2010/A2:2014 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-1: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - MEASURING APPARATUS (CISPR 16-1-1:2010/A2:2014)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective