• Shopping Cart
    There are no items in your cart

BS EN 60317-17:2010

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Specifications for particular types of winding wires Polyvinyl acetal enamelled rectangular copper wire, class 105

Available format(s)

Hardcopy , PDF

Superseded date

05-08-2020

Superseded by

BS EN IEC 60317-17:2020

Language(s)

English

Published date

30-06-2010

€140.23
Excluding VAT

INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions and general notes on methods
   of test and appearance
4 Dimensions
5 Electrical resistance
6 Elongation
7 Springiness
8 Flexibility and adherence
9 Heat shock
10 Cut-through
11 Resistance to abrasion
12 Resistance to solvents
13 Breakdown voltage
14 Continuity of insulation
15 Temperature index
16 Resistance to refrigerants
17 Solderability
18 Heat or solvent bonding
19 Dielectric dissipation factor
20 Resistance to transformer oil
21 Loss of mass
23 Pin hole test
30 Packaging
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Describes the requirements of enamelled rectangular copper winding wire of class 105 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements.

Committee
W/-
DevelopmentNote
Renumbers and supersedes BS 6811-4.5(1993) 1996 version incorporates amendment 9068 to BS 6811-4.5(1993). To be read in conjunction with BS EN 60317-0.2. (10/2005) Supersedes 09/30200536 DC. (06/2010)
DocumentType
Standard
Pages
14
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

This part of IEC 60317 specifies the requirements of enamelled rectangular copper winding wire of class 105 with a sole coating based on polyvinyl acetal resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements.

NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics.

Class 105 is a thermal class that requires a minimum temperature index of 105 and a heat shock temperature of at least 155 °C.

The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved.

The range of nominal conductor dimensions covered by this standard is

width: min. 2,00 mm max. 16,00 mm;
thickness: min. 0,80 mm max. 5,60 mm.

Wires of grade 1 and grade 2 are included in this specification and apply to the complete range of conductors.

The specified combinations of width and thickness as well as the specified ratio width/thickness are given in IEC 60317-0-2.

EN 60851-4:2016 Winding wires - Test methods - Part 4: Chemical properties
IEC 60317-0-2:2013 Specifications for particular types of winding wires - Part 0-2: General requirements - Enamelled rectangular copper wire
EN 60317-0-2:2014 Specifications for particular types of winding wires - Part 0-2: General requirements - Enamelled rectangular copper wire
IEC 60851-4:2016 Winding wires - Test methods - Part 4: Chemical properties

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.