Skip to content
Please enter a keyword to search

  • BS EN 60352-4:1995

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Solderless connections Solderless non-accessible insulation displacement connections. General requirements, test methods and practical guidance

    Available format(s):  Hardcopy, PDF

    Superseded date:  07-08-2020

    Language(s):  English

    Published date:  16-11-2001

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    SECTION 1: GENERAL
    1 Scope
    2 Object
    3 Normative references
    4 Definitions
    5 IEC type designation
    SECTION 2: REQUIREMENTS
    6 Workmanship
    7 Tools
    8 Insulation displacement termination (ID termination)
    9 Wires
    10 Non-accessible insulation displacement connections
       (ID connections)
    SECTION 3: TESTS
    11 Testing
    12 Type tests
    13 Test schedules
    SECTION 4: PRACTICAL GUIDANCE
    14 General
    15 Tool information
    16 Termination information
    17 Wire information
    18 Connection information
    19 ID connections, open housing design
    20 ID connections, closed housing design
    21 General additional information about ID connections
       as part of a multi-pole connector
    22 Final remarks
    Annex ZA (normative) Other international publications
              quoted in this standard with references of the
              relevant European publications

    Abstract - (Show below) - (Hide below)

    Applies to non-accessible ID connections for which the tests and measurements of Section 3 are suitable and which are made with: - appropriately designed ID terminations; - wires having solid round conductors of 0,25 mm to 3,6 mm nominal diameter; - wires having stranded conductors of 0,05 square meter to 10 square meter cross-section; for use in telecommunication equipment and in electronic devices employing similar techniques.

    General Product Information - (Show below) - (Hide below)

    Committee EPL/48/-/2
    Development Note Supersedes 93/200051 DC. Also numbered as IEC 60352-4. (12/2001)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS EN 61076-4:1997 Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications Sectional specification. Printed board connectors

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC GUIDE 109:2012 Environmental aspects - Inclusion in electrotechnical product standards
    IEC 60352-3:1993 Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    IEC 60512-6:1984 Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 6: Climatic tests and soldering tests
    IEC 60068-2-60:2015 RLV Environmental testing - Part 2-60: Tests - Test Ke: Flowing mixed gas corrosion test
    EN 60352-3:1994 Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance
    EN 60068-1:2014 Environmental testing - Part 1: General and guidance
    ISO 1463:2003 Metallic and oxide coatings Measurement of coating thickness Microscopical method
    EN 60512-1:2001 Connectors for electronic equipment - Tests and measurements - Part 1: General
    EN 60512-11-7:2003 Connectors for electronic equipment - Tests and measurements - Part 11- 7: Climatic tests - Test 11g: Flowing mixed gas corrosion test
    IEC 60512-11-7:2003 Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests - Test 11g: Flowing mixed gas corrosion test
    IEC 60512-4:1976 Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 4: Dynamic stress tests
    IEC 60512-5:1992 Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 5: Impact tests (free components), static load tests (fixed components), endurance tests and overload tests
    IEC 60512-1:2001 Connectors for electronic equipment - Tests and measurements - Part 1: General
    IEC 60050-581:2008 International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
    IEC 60189-3:2007 Low-frequency cables and wires with PVC insulation and PVC sheath - Part 3: Equipment wires with solid or stranded conductor wires, PVC insulated, in singles, pairs and triples
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective