• BS EN 61037 : 1993

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    ELECTRICITY METERING - TARIFF AND LOAD CONTROL - PARTICULAR REQUIREMENTS FOR ELECTRONIC RIPPLE CONTROL RECEIVERS

    Available format(s):  Hardcopy, PDF

    Superseded date:  21-01-2005

    Language(s):  English

    Published date:  01-01-1993

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Committees responsible
    National foreword
    Specification
    1. Scope
    2. Normative references
    3. Definitions
    4. Requirements
    5. Tests and test conditions
    Annexes
    A. Relationship between ambient air temperature and
         relative humidity
    B. Reference and limiting values of the influence
         quantities
    C. Electromagnet for testing the influence of
         externally-produced magnetic fields
    D. Harmonic levels
    E. Selection of frequency for tests with harmonics
    F. Combination of parameters for operation and non-
         operation tests
    G. Acceptance tests
    H. Code terms
    J. Example of a test configuration
    K. Values of the influence quantities for the different
         tests
    ZA. Normative references to international publications
         with their corresponding European publications
    Figure E.1 Examples for selection of the frequency Hc
    Figure E.2 Frequency deviations for measurement of the
                 disturbance limit curve
    Tables
    1. Clearances and creepage distances for the terminal
         block
    2. Temperature range
    3. Relative humidity
    4. Rated breaking voltages
    5. Rated breaking currents

    Abstract - (Show below) - (Hide below)

    Specifies the tests and requirements for electronic ripple control receivers used for the control of electricity loading and electricity consumption tariffs.

    General Product Information - (Show below) - (Hide below)

    Committee PEL/13
    Development Note Renumbers and supersedes BS 7401(1990). 1993 version incorporates amendment 7673 to BS 7401(1990). Supersedes 89/29115 DC. (12/2005)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    BS 4727-1:GRP04(1986) : 1986 GLOSSARY OF ELECTROTECHNICAL POWER TELECOMMUNICATION ELECTRONICS LIGHTING AND COLOUR TERMS - TERMS COMMON TO POWER TELECOMMUNICATIONS & ELECTRONICS - MEASUREMENT TERMINOLOGY
    BS EN 55022 : 2010 INFORMATION TECHNOLOGY EQUIPMENT - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT
    BS 7003(1988) : 1988 SPECIFICATION FOR SPRING-OPERATED IMPACT-TEST APPARATUS AND ITS CALIBRATION
    BS 2011-2.1B(1977) : 1977 ENVIRONMENTAL TESTING - TESTS - TEST B. DRY HEAT
    BS 2011-2.1DB(1981) : 1981 ENVIRONMENTAL TESTING - TESTS - TEST DB AND GUIDANCE: DAMP HEAT, CYCLIC (12 + 12 HOUR CYCLE)
    IEC 60801-4 : 1ED 88 ELECTROMAGNETIC COMPATIBILITY FOR INDUSTRIAL PROCESS MEASUREMENT AND CONTROL EQUIPMENT - ELECTRICAL FAST TRANSIENT/BURST REQUIREMENTS
    BS 923-1(1990) : 1990 GUIDE ON HIGH-VOLTAGE TESTING TECHNIQUES - GENERAL
    BS 923-2(1980) : 1980 GUIDE ON HIGH-VOLTAGE TESTING TECHNIQUES - TEST PROCEDURES
    BS EN 61000-4-2 : 2009 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-2: TESTING AND MEASUREMENT TECHNIQUES - ELECTROSTATIC DISCHARGE IMMUNITY TEST
    BS 923-3(1980) : 1980 GUIDE ON HIGH-VOLTAGE TESTING TECHNIQUES - MEASURING DEVICES
    BS 2011-2.1A(1990) : 1990 AMD 7783 ENVIRONMENTAL TESTING - TESTS - TEST A: COLD
    BS 6458-2.1:1984 FIRE HAZARD TESTING FOR ELECTROTECHNICAL PRODUCTS - TEST METHODS - GLOW-WIRE TEST
    BS 923-4(1980) : 1980 GUIDE ON HIGH-VOLTAGE TESTING TECHNIQUES - APPLICATION GUIDE FOR MEASURING DEVICES
    BS 2011-2.1EA(1988) : 1988 AMD 7814 ENVIRONMENTAL TESTING - TEST - TEST EA: SHOCK
    IEC 60269-3:2010+AMD1:2013 CSV Low-voltage fuses - Part 3: Supplementary requirements for fuses foruse by unskilled persons (fuses mainly for household or similar applications) - Examples of standardized systems of fuses A to F
    IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test
    BS 2011-2.1FC(1983) : 1983 ENVIRONMENTAL TESTING - TESTS - TEST FC: VIBRATION (SINUSOIDAL)
    BS EN 60529:1992+A2:2013 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE)
    BS 2757(1986) : 1986 METHOD FOR DETERMINING THE THERMAL CLASSIFICATION OF ELECTRICAL INSULATION
    IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations
    BS 6001-1(1999) : 1999 SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION
    PD 6499:1981 (published 1981-08) Guide to insulation co-ordination within low-voltage systems including clearances and creepage distances for equipment
    BS 6217(1981) : 1981 GUIDE TO GRAPHICAL SYMBOLS FOR USE ON ELECTRICAL EQUIPMENT
    BS 5685-2:1986 ELECTRICITY METERS - SPECIFICATION FOR SINGLE-PHASE COIN OPERATED PREPAYMENT FLAT RATE AND TWO-PART TARIFF WATT-HOUR METERS OF CLASS 2 AND FIXED CHARGE COLLECTORS OF CLASS 2
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective