Connectors for electronic equipment. Product requirements Rectangular connectors. Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface. Variant 14 related to IEC 61076-3-106. Push-pull coupling

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

30-09-2009

Publisher

British Standards Institution

€165.94

Excluding VAT

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

1 Scope
2 General data
  2.1 Normative references
  2.2 Terms and definitions
3 Dimensional information
  3.1 Common features
  3.2 General
  3.3 Contact arrangement of all connector types
  3.4 IP65 and IP67 sealing
  3.5 Dimensions, fixed connector
  3.6 Dimensions, free connector
  3.7 Termination and mounting information
      3.7.1 General
      3.7.2 Mounting information for fixed connector
4 Gauges
  4.1 Connectors, IEC 60603-7 interface
5 Characteristics
  5.1 Climatic category
  5.2 Electrical characteristics
      5.2.1 Clearance and creepage distances
      5.2.2 Voltage proof
      5.2.3 Current-carrying capacity
      5.2.4 Mating cycles with power applied
      5.2.5 Initial contact resistance
      5.2.6 Input to output resistance
      5.2.7 Resistance unbalance
      5.2.8 Initial insulation resistance
  5.3 Transmission characteristics
      5.3.1 General
  5.4 Mechanical
      5.4.1 Mechanical operation
      5.4.2 Effectiveness of connector coupling devices
            transversal
      5.4.3 Effectiveness of connector coupling devices
      5.4.4 Engagement and separation forces
6 Test schedule
  6.1 General
  6.2 Test procedures and measuring methods
  6.3 Preconditioning
  6.4 Wiring and mounting of specimens
      6.4.1 Wiring
      6.4.2 Mounting
  6.5 Arrangement for contact resistance test
  6.6 Arrangement for dynamic stress tests (test phase AP2)
  6.7 Basic (minimum) test schedule
  6.8 Full test schedule
      6.8.1 General
      6.8.2 Test group P - Preliminary
      6.8.3 Test group P
      6.8.4 Test group AP
      6.8.5 Test group BP
      6.8.6 Test group CP
      6.8.7 Test group DP - Electrical load and temperature
      6.8.8 Test group EP - Signal integrity
Annex ZA (normative) - Normative references to international
                       publications with their corresponding
                       European publications

Describes rectangular protective housings with push-pull coupling for upgrading existing 8-way shielded and unshielded connectors utilizing the interface described in IEC 60603-7-2, IEC 60603-7-3, IEC 60603-7-4, IEC 60603-7-41, IEC 60603-7-5, IEC 60603-7-51, IEC 60603-7-7 and IEC 60603-7-71 to IP65 and IP67 ratings according to IEC 60529, for use in industrial environments.

Committee	EPL/48
DocumentType	Standard
Pages	22
PublisherName	British Standards Institution
Status	Current

IEC 61076-3-117:2009 covers rectangular protective housings with push-pull coupling for upgrading existing 8-way shielded and unshielded connectors utilizing the interface described in IEC 60603-7-2, IEC 60603-7-3, IEC 60603-7-4, IEC 60603-7-41, IEC 60603-7-5, IEC 60603-7-51, IEC 60603-7-7 and IEC 60603-7-71 to IP65 and IP67 ratings according to IEC 60529, for use in industrial environments. Common mating configurations for all variants of the 8-way shielded and unshielded connectors are defined in IEC 60603-7.

Standards	Relationship
IEC 61076-3-117:2009	Identical
EN 61076-3-117:2009	Identical

IEC 61076-1:2006	Connectors for electronic equipment - Product requirements - Part 1: Generic specification
IEC 60068-1:2013	Environmental testing - Part 1: General and guidance
EN 60512-1-100:2012	Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications
EN 60068-1:2014	Environmental testing - Part 1: General and guidance
EN 61076-1:2006	Connectors for electronic equipment - Product requirements - Part 1: Generic specification
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV	Degrees of protection provided by enclosures (IP Code)
IEC 60512-1-100:2012	Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications
EN 60664-1:2007	Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN 60529:1991/AC:2016-12	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN 60068-2-30:2005	Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
IEC 60068-2-14:2009	Environmental testing - Part 2-14: Tests - Test N: Change of temperature
IEC 60664-1:2007	Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN 60068-2-14:2009	Environmental testing - Part 2-14: Tests - Test N: Change of temperature
IEC 60050-581:2008	International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
IEC 60068-2-30:2005	Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Get in touch with us

BS EN 61076-3-117:2009

Table of Contents

Abstract

General Product Information

Scope

International Equivalents

Standards Referencing This Book

Category

Subcategory