• BS EN 62006:2011

    Current The latest, up-to-date edition.

    Hydraulic machines. Acceptance tests of small hydroelectric installations

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  30-06-2011

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 Scope
    2 Normative references
    3 Terms, definitions and schematic layout
    4 Nature and extent of guarantees
    5 Safety tests (commissioning)
    6 Trial operating and reliability tests (commissioning)
    7 Performance guarantees and tests
    8 Computation of results and comparison to the guarantee
    9 Error analysis
    10 Other guarantees
    Annex A (normative) - Terms, definitions, symbols and units
    Annex B (normative) - Head definition
    Annex C (normative) - Method of speed measurements
    Annex D (normative) - Power output measurement
    Annex E (normative) - Methods of discharge measurement
    Annex F (informative) - Plant condition
    Annex G (informative) - Commissioning
    Annex H (informative) - Performance test efficiency calculation
    Annex I (informative) - Cam correlation test
    Bibliography
    Annex ZA (normative) - Normative references to international
             publications with their corresponding
             European publications

    Abstract - (Show below) - (Hide below)

    Describes the test, the measuring methods and the contractual guarantee conditions for field acceptance tests of the generating machinery in small hydroelectric power installations.

    Scope - (Show below) - (Hide below)

    IEC 62006:2010 defines the test, the measuring methods and the contractual guarantee conditions for field acceptance tests of the generating machinery in small hydroelectric power installations. It applies to installations containing impulse or reaction turbines with unit power up to about 15 MW and reference diameter of about 3 m. The driven generator can be of synchronous or asynchronous type. This International Standard contains information about most of the tests required for acceptance of the hydraulic turbine such as safety approval tests, trial operating and reliability tests, as well for verification of cavitation, noise and vibration conditions, if required. This standard represents the typical methods used on smaller hydroelectric installations, and is divided into three classes as follows:
    Class A: Default, normal test program (panel measurement), to determine the maximum output of the installation.
    Class B: Recommended, extended test program, to determine the performance characteristics of the installation.
    Class C: Optional, comprehensive test program, to determine the absolute efficiency of the installation.
    All classes contain safety tests, trial operating tests, and reliability tests. This standard gives all necessary references for the contract in order to execute the test, evaluate, calculate and compare the result to the guarantee for all the classes A, B and C.

    General Product Information - (Show below) - (Hide below)

    Committee MCE/15
    Development Note Supersedes 06/19982093 DC. (06/2011)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60545:1976 Guide for commissioning, operation and maintenance of hydraulic turbines
    ISO 5168:2005 Measurement of fluid flow — Procedures for the evaluation of uncertainties
    ISO 4373:2008 Hydrometry Water level measuring devices
    EN ISO 1680:2013 Acoustics - Test code for the measurement of airborne noise emitted by rotating electrical machines (ISO 1680:2013)
    ISO 3354:2008 Measurement of clean water flow in closed conduits — Velocity-area method using current-meters in full conduits and under regular flow conditions
    IEC TR 61364:1999 Nomenclature for hydroelectric powerplant machinery
    IEC 61116:1992 Electromechanical equipment guide for small hydroelectric installations
    ISO 1940-1:2003 Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances
    IEC 60308:2005 Hydraulic turbines - Testing of control systems
    ISO 1680:2013 Acoustics — Test code for the measurement of airborne noise emitted by rotating electrical machines
    IEC 60193:1999 Hydraulic turbines, storage pumps and pump-turbines - Model acceptance tests
    IEEE 810-2015 IEEE Standard for Hydraulic Turbine and Generator Shaft Couplings and Shaft Runout Tolerances
    IEC 60041:1991 Field acceptance tests to determine the hydraulic performance of hydraulic turbines, storage pumps and pump-turbines
    EN 60193:1999 Hydraulic turbines, storage pumps and pump-turbines - Model acceptance tests
    ISO 7919-5:2005 Mechanical vibration Evaluation of machine vibration by measurements on rotating shafts Part 5: Machine sets in hydraulic power generating and pumping plants
    ISO 3746:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
    EN 61362:2012 Guide to specification of hydraulic turbine governing systems
    EN 60041:1994 Field acceptance tests to determine the hydraulic performance of hydraulic turbines, storage pumps and pump-turbines
    EN ISO 3746:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
    EN 60308:2005 Hydraulic turbines - Testing of control systems
    ISO 2954:2012 Mechanical vibration of rotating and reciprocating machinery — Requirements for instruments for measuring vibration severity
    IEC 61362:2012 Guide to specification of hydraulic turbine governing systems
    EN 60651:1994/A2:2001 SOUND LEVEL METERS (IEC 60651:1979/A2:2000)
    ISO 2186:2007 Fluid flow in closed conduits — Connections for pressure signal transmissions between primary and secondary elements
    IEC 61260:1995 Electroacoustics - Octave-band and fractional-octave-band filters
    ISO 3966:2008 Measurement of fluid flow in closed conduits Velocity area method using Pitot static tubes
    ISO 3455:2007 Hydrometry Calibration of current-meters in straight open tanks
    IEC 60651:1979+AMD1:1993+AMD2:2000 CSV Sound level meters
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective