• BS EN ISO 4894-2:1999

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Plastics. Styrene/acrylonitrile (SAN) copolymer moulding and extrusion materials Preparation of test specimens and determination of properties

    Available format(s):  Hardcopy, PDF

    Superseded date:  07-04-2020

    Language(s):  English

    Published date:  15-11-1999

    Publisher:  British Standards Institution

    Add To Cart

    Abstract - (Show below) - (Hide below)

    Defines the procedures for preparing test specimens and test procedures to be used to determine the properties of SAN extrusion and moulding material. Also gives requirements for handling test material and for conditioning both the test material prior to moulding and the specimens before testing.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/82
    Development Note Together with BS EN ISO 4894-1 supersedes BS 4936(1987) Supersedes and renumbers BS ISO 4894-2 (10/1999)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
    ISO 4589-3:2017 Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test
    ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
    ISO 1656:2014 Rubber, raw natural, and rubber latex, natural Determination of nitrogen content
    ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
    ISO 3167:2014 Plastics Multipurpose test specimens
    ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
    ISO 4581:1994 Plastics Styrene/acrylonitrile copolymers Determination of residual acrylonitrile monomer content Gas chromatography method
    ISO 294:1995 Plastics Injection moulding of test specimens of thermoplastic materials
    ISO 8256:2004 Plastics — Determination of tensile-impact strength
    ISO 10350:1993 Plastics Acquisition and presentation of comparable single-point data
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 4894-1:1997 Plastics Styrene/acrylonitrile (SAN) moulding and extrusion materials Part 1: Designation system and basis for specifications
    ISO 1183:1987 Plastics Methods for determining the density and relative density of non-cellular plastics
    ISO 1210:1992 Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source
    ISO 2561:2012 Plastics — Determination of residual styrene monomer in polystyrene (PS) and impact-resistant polystyrene (PS-I) by gas chromatography
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ISO 62:2008 Plastics Determination of water absorption
    ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
    ISO 4589-2:2017 Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
    ISO 2818:1994 Plastics — Preparation of test specimens by machining
    ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
    ISO 75-3:2004 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
    ISO 178:2010 Plastics Determination of flexural properties
    ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    • Access your standards online with a subscription


      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective