Skip to content
Please enter a keyword to search

  • BS EN ISO 8835-3 : 2009

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    INHALATIONAL ANAESTHESIA SYSTEMS - PART 3: TRANSFER AND RECEIVING SYSTEMS OF ACTIVE ANAESTHETIC GAS SCAVENGING SYSTEMS

    Available format(s):  Hardcopy, PDF

    Superseded date:  28-02-2013

    Language(s):  English

    Published date:  01-01-2010

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General requirements and alternative test methods
    5 Patient and environmental protection
    6 Connectors
    7 Transfer systems
    8 Receiving systems
    9 Extract flow resistance
    10 Electrical requirements
    11 Information to be supplied by the manufacturer
    12 Marking
    13 Colour coding
    Annex A (informative) - Typical test arrangement and
            method for pressure measurement at inlet to
            AGSS
    Annex B (informative) - Typical test arrangement and
            method for sub-atmospheric pressure limitation
    Annex C (informative) - Typical test arrangement and
            method for testing of induced flow
    Annex D (informative) - Typical test arrangement and
            method for resistance to extract flow
    Annex E (informative) - Typical test arrangement and
            method for spillage
    Annex F (informative) - Rationale
    Annex G (informative) - Environmental aspects
    Bibliography
    Annex ZA (informative) - Relationship between this
             European Standard and the Essential
             Requirements of EU Directive 93/42/EEC

    Abstract - (Show below) - (Hide below)

    Describes requirements for transfer and receiving systems of active anaesthetic gas scavenging systems (active AGSSs) intended to reduce exposure of healthcare personnel to anaesthetic gases and vapours while providing patient protection (e.g. against excessive flow and pressure).

    General Product Information - (Show below) - (Hide below)

    Committee CH/121/1
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60601-1:2005+AMD1:2012 CSV Medical electrical equipment - Part 1: General requirements for basic safety and essential performance
    ISO 5356-1:2015 Anaesthetic and respiratory equipment Conical connectors Part 1: Cones and sockets
    ISO 9170-2:2008 Terminal units for medical gas pipeline systems — Part 2: Terminal units for anaesthetic gas scavenging systems
    ISO 7396-2:2007 Medical gas pipeline systems Part 2: Anaesthetic gas scavenging disposal systems
    ISO/TS 18835:2004 Inhalational anaesthesia systems Draw-over vaporizers and associated equipment
    ISO 5356-2:2012 Anaesthetic and respiratory equipment — Conical connectors — Part 2: Screw-threaded weight-bearing connectors
    ISO 21647:2004 Medical electrical equipment Particular requirements for the basic safety and essential performance of respiratory gas monitors
    ISO 5359:2014 Anaesthetic and respiratory equipment Low-pressure hose assemblies for use with medical gases
    IEC 60079-11:2011 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
    IEC 60601-2-13:2003+AMD1:2006 CSV Medical electrical equipment - Part 2-13: Particular requirements for the safety and essential performance of anaesthetic systems
    ISO 9170-1:2017 Terminal units for medical gas pipeline systems — Part 1: Terminal units for use with compressed medical gases and vacuum
    ISO 14971:2007 Medical devices Application of risk management to medical devices
    ISO 7000:2014 Graphical symbols for use on equipment Registered symbols
    ISO 4135:2001 Anaesthetic and respiratory equipment Vocabulary
    ISO 8835-2:2007 Inhalational anaesthesia systems Part 2: Anaesthetic breathing systems
    ISO 594-2:1998 Conical fittings with 6 % (Luer) taper for syringes, needles and certain other medical equipment Part 2: Lock fittings
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective