Credit card payment only is accepted for this order because it contains a mix of both publications and training products.
Invalid username/password. Please try again.
xyz
Radio equipment used in mobile services. Methods of measurement Data equipment
:
Available format(s): Hardcopy, PDF
Language(s): English
Published date: 15-03-2000
Publisher: British Standards Institution
Foreword1 General 1.1 Scope and object 1.2 Emission characteristics 1.3 System characteristics 1.4 Normative references2 Terms and definitions3 Test conditions 3.1 Standard test conditions 3.2 Supplementary test conditions 3.3 Characteristics of the measuring equipment4 Measurements of receiver-decoder radio-frequency parameters 4.1 Sensitivity (data) 4.2 Adjacent radio-frequency signal selectivity (data) 4.3 Co-channel interference rejection (data) 4.4 Adjacent-channel selectivity (data) 4.5 Spurious response immunity (data) 4.6 Intermodulation immunity (data) 4.7 Sensitivity under multipath propagation conditions (data) 4.8 Acceptable radio-frequency displacement (data) 4.9 Impulsive-noise tolerance (data)5 Measurement of receiver-decoder radio-frequency parameters (selective calling only) 5.1 Protection from radio-frequency intermodulation false operation (selective calling) 5.2 False response due to noise (selective calling) ponentsing calling) 5.3 Signalling attack time (selective calling) 5.4 Recovery time (selective calling) 5.5 Required protection time (selective calling) 5.6 Signal-to-residual output-power ratio (selective calling)6 Measurements of receiver-decoder conducted and radiated spurious components 6.1 Conducted spurious components (data and selective calling) 6.2 Radiated spurious components (data)7 Measurements of encoder-transmitters radio-frequency parameters 7.1 Frequency error (data) 7.2 Average radio-frequency output power (data) 7.3 Spurious narrow bandwidth radio-frequency emission power (data) 7.4 Adjacent and alternate channel power (data)8 Audio-frequency band measurements of encoder output characteristics (selective calling) 8.1 Tone pulse-rise time (selecting calling) 8.2 Tone pulse duration (selecting calling) 8.3 Tone pulse-decay time (selecting calling) 8.4 Frequency of tone(s) (selecting calling) 8.5 RMS voltage of tone(s) (selecting calling) 8.6 Encoder overall operate time (selecting calling)9 Audio-frequency band measurements of decoder characteristics (selecting calling) 9.1 Decoder operation level range (selecting calling) 9.2 Decoder attack time (selecting calling) 9.3 Decoder recovery time (selecting calling) 9.4 Decoder required protection time (selecting calling) 9.5 Decoder alarm time (selecting calling)10 Overall measurements in simulated systems (selecting calling) 10.1 General 10.2 Supplementary conditions of measurement for system response times 10.3 System overall operate time (selecting calling) 10.4 System recovery time (selecting calling)11 Measurement of receiver-decoder radio-frequency parameter (integral antenna) 11.1 Radiation sensitivity (data) 11.2 Selectivity (data) 11.3 Acceptable radio-frequency displacement 11.4 Impulsive-noise tolerance (integral antenna)12 Measurements of encoder-transmitters radio-frequency parameters (integral antenna) 12.1 Radiated radio-frequency power (data)Annex A (normative) Examples of combining networksAnnex B (normative) Recommended characteristics of measuring equipment and methods of testAnnex C (normative) Rayleigh fading simulatorAnnex D (informative) Intermodulation responseAnnex E (normative) Accuracy and dispersion of methods of measurement and compliance tests for sensitivity (data and selective calling) and degradation measurements (data and selective calling)Annex F (normative) Mean time between false calling responses (M) (selecting calling)Annex G (normative) General information on impulse noise and random impulse generatorAnnex H (informative) Examples of a mains power line impedance stabilization networkAnnex I (informative) Measuring error of the occupied bandwidth centre frequency using spectrum analyser
Defines mobile radio receivers and transmitters, for the transmission of data signals having the emission characteristics given in 1.1. The following type of signals are covered; character strings, selective calling, bit streams, and messages.
Refers specifically to mobile radio transmitters and receivers for the transmission of data (telegraphy) signals. Is intended to be used in conjunction with IEC 60489-1. The terms and definition and the condition of measurement set forth in this standard are intended for type and acceptance tests. Covers bit streams, character strings, messages and selective calling.
AUD CAD CHF CNY DKK EUR GBP HKD IDR INR JPY KRW MXN NOK NZD SEK SGD USD ZAR
Unfortunately, this product is not available for purchase in your region.
Features
Get in touch with us
Loading..
A free alerting service to track changes to standards.
Once you've completed your purchase you'll get a link to My Orders on: -the Confirmation page of check out -and by email You'll be able to access your Multi User Orders to add Users.
You have selected more than three (3) participants. Please contact our Customer Service team.
You have already added this product in the cart. If you would like to add additional copies of this product please adjust the Quantity in the cart. For more than 10 copies, please contact our Customer Support team on +353 (0)1 857 6730.
You have selected more than three (3) trainings. Please contact our Customer Service team.Please contact our Customer Service team on Email: sales@saiglobal.com Phone: 131 242 (Within Australia)
You have already added a product with different Currency. Please change the currency.
This product cannot be added to your cart right now. Please contact our Customer Service team on Email: info@standards.iePhone: +353(0)1 857 6730
You have already saved 6 Quotes. Please contact our Customer Service Team.