Skip to content
Please enter a keyword to search

  • BS ISO 1101:1983

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Technical drawings. Geometrical tolerancing. Tolerancing of form, orientation, location and run-out. Generalities, definitions, symbols, indications on drawings

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-10-2007

    Language(s):  English

    Published date:  15-07-2000

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Basic concepts
    5 Symbols
    6 Tolerance frame
    7 Toleranced features
    8 Tolerance zones
    9 Datums
    10 Supplementary indications
    11 Theoretically exact dimensions (TED)
    12 Restrictive specifications
    13 Projected tolerance zone
    14 Maximum material requirement
    15 Least material requirement
    16 Free state condition
    17 Interrelationship of geometrical tolerances
    18 Definitions of geometrical tolerances
    Annexes
    A Former practices
    B Assessment of geometrical deviations
    C Relation to the GPS matrix model
    Bibliography

    Abstract - (Show below) - (Hide below)

    Provides basic information and gives requirements for the geometrical tolerancing of workpieces. It represents the initial basis and defines the fundamentals for geometrical tolerancing.

    General Product Information - (Show below) - (Hide below)

    Committee TPR/1
    Development Note Supersedes BS 308-1(1993) and BS 308-2(1985). (10/2002) Supersedes BS 308-3(1990). (03/2003) Supersedes 95/702648 DC. (01/2005) Renumbered and superseded by BS EN ISO 1101. (10/2007)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS DD16792(2002) : 2002 TECHNICAL PRODUCT DOCUMENTATION (TPD) - DIGITAL PRODUCT DEFINITION DATA PRACTICES
    BS 8888:2008 Technical product specification. Specification
    BS 8888:2002 Technical product documentation (TPD). Specification for defining, specifying and graphically representing products
    PD 8888:2001 Technical product documentation (TPD). An interim report
    BS 4311-1:2007 Gauge blocks manufactured to imperial specification Specification and validation
    SBAC TS 66 : 6 DRAUGHTING AND PART NUMBERING PROCEDURES FOR A¦D¦S DRAWINGS
    BS 8888:2000 Technical product documentation (TPD). Specification for defining, specifying and graphically representing products
    BS 8888:2004 TECHNICAL PRODUCT SPECIFICATION (TPS) - SPECIFICATION
    BS 4311(2007) : 2007 GAUGE BLOCKS MANUFACTURED TO IMPERIAL SPECIFICATION - SPECIFICATION, VALIDATION AND ACCESSORIES
    BIP 3016 : 2004 BS 8888(2004) - TECHNICAL PRODUCT SPECIFICATION CD-ROM
    BS 8888:2006 Technical product specification (TPS). Specification

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/TS 12181-2:2003 Geometrical Product Specifications (GPS) Roundness Part 2: Specification operators
    ISO/TS 12781-1:2003 Geometrical Product Specifications (GPS) Flatness Part 1: Vocabulary and parameters of flatness
    ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
    ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
    ISO/TS 17450-2:2002 Geometrical product specifications (GPS) General concepts Part 2: Basic tenets, specifications, operators and uncertainties
    ISO 5459:2011 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
    ISO 2692:2014 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
    ISO/TS 12780-1:2003 Geometrical Product Specifications (GPS) Straightness Part 1: Vocabulary and parameters of straightness
    ISO 128-24:2014 Technical drawings General principles of presentation Part 24: Lines on mechanical engineering drawings
    ISO 7083:1983 TECHNICAL DRAWINGS - SYMBOLS FOR GEOMETRICAL TOLERANCING - PROPORTIONS AND DIMENSIONS
    ISO 3040:2016 Geometrical product specifications (GPS) Dimensioning and tolerancing Cones
    ISO/TR 5460:1985 Technical drawings Geometrical tolerancing Tolerancing of form, orientation, location and run-out Verification principles and methods Guidelines
    ISO 14660-2:1999 Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature
    ISO 3098-2:2000 Technical product documentation — Lettering — Part 2: Latin alphabet, numerals and marks
    ISO 10578:1992 Technical drawings Tolerancing of orientation and location Projected tolerance zone
    ISO/TS 12180-2:2003 Geometrical Product Specifications (GPS) Cylindricity Part 2: Specification operators
    ISO 3098-0:1997 Technical product documentation Lettering Part 0: General requirements
    ISO/TS 12781-2:2003 Geometrical Product Specifications (GPS) Flatness Part 2: Specification operators
    ISO 14660-1:1999 Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions
    ISO/TS 12180-1:2003 Geometrical Product Specifications (GPS) Cylindricity Part 1: Vocabulary and parameters of cylindrical form
    ISO 1660:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing
    ISO 10579:2010 Geometrical product specifications (GPS) Dimensioning and tolerancing Non-rigid parts
    ISO 5458:1998 Geometrical Product Specifications (GPS) Geometrical tolerancing Positional tolerancing
    ISO/TS 12181-1:2003 Geometrical Product Specifications (GPS) Roundness Part 1: Vocabulary and parameters of roundness
    ISO/TS 12780-2:2003 Geometrical Product Specifications (GPS) Straightness Part 2: Specification operators
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective