Skip to content
Please enter a keyword to search

  • BS ISO 17467-1:2012

    Current The latest, up-to-date edition.

    Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems jointed by solvent cement General

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  30-11-2012

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Material
    Annex A (normative) - Assessment of the degree of pigment
            or carbon black dispersion in unplasticized
            polyamide compounds
    Annex B (normative) - Chemical resistance
    Annex C (informative) - Design guidance
    Annex D (normative) - Hoop stress at burst
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the general properties of unplasticized polyamide (PA-U) compounds for the manufacturing of pipes, fittings and valves made from such compounds, intended to be buried and used for the supply of gaseous fuels for maximum operating pressure up to and including 4 bar.

    Scope - (Show below) - (Hide below)

    This part of ISO17467 specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacturing of pipes, fittings and valves made from such compounds, intended to be buried and used for the supply of gaseous fuels for maximum operating pressure up to and including 4 bar.

    It also specifies the test parameters for the test methods to which it refers.

    This part of ISO17467 specifies a calculation and design scheme on which the maximum operating pressure (MOP) of piping systems is based.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/88/2
    Development Note Supersedes 11/30248330 DC. (11/2012)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    AS 2944.2-2007 Plastics pipes and fittings for gas reticulation Polyamide fittings (Reconfirmed 2023)
    ISO 1874-1:2010 Plastics Polyamide (PA) moulding and extrusion materials Part 1: Designation system and basis for specification
    AS/NZS 4645.3:2008 Gas distribution networks Plastics pipe systems
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
    ISO 6964:1986 Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification
    ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
    ISO 9080:2012 Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
    ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
    ISO 3:1973 Preferred numbers Series of preferred numbers
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 1874-2:2012 Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
    ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
    ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST)
    ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
    AS 2943-2007 Plastics pipes and fittings for gas reticulation - Polyamide compounds (Reconfirmed 2022)
    ISO 16871:2003 Plastics piping and ducting systems — Plastics pipes and fittings — Method for exposure to direct (natural) weathering
    ISO 472:2013 Plastics Vocabulary
    ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
    ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
    ISO 307:2007 Plastics Polyamides Determination of viscosity number
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ASTM F 1733 : 2013 : REDLINE Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
    ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
    ISO 17467-2:2012 Plastics piping systems for the supply of gaseous fuels Unplasticized polyamide (PA-U) piping systems jointed by solvent cement Part 2: Pipes
    ISO 15512:2016 Plastics Determination of water content
    ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
    ISO 13480:1997 Polyethylene pipes Resistance to slow crack growth Cone test method
    ISO 6259-3:2015 Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    AS 2944.1-2007 Plastics pipes and fittings for gas reticulation Polyamide pipes (Reconfirmed 2023)
    ISO 2505:2005 Thermoplastics pipes — Longitudinal reversion — Test method and parameters
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective