BS ISO 18099:2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Thermal insulating products for building equipment and industrial installations. Determination of the coefficient of thermal expansion
Available format(s)
Hardcopy , PDF
Superseded date
12-09-2022
Superseded by
Language(s)
English
Published date
30-04-2013
Publisher
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Terms and definitions
3 Principle
4 Apparatus
5 Test specimens
6 Procedure
7 Calculation and expression of results
8 Accuracy of measurement
9 Test report
Describes the equipment and procedures for determining the coefficient of linear thermal expansion.
| Committee |
B/540/8
|
| DevelopmentNote |
Supersedes 12/30266476 DC. (04/2013)
|
| DocumentType |
Standard
|
| Pages |
20
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This International Standard specifies the equipment and procedures for determining the coefficient of linear thermal expansion. It is applicable to thermal insulating products within the temperature range 196°C to 850°C, subject to the possible temperature limitation of the test specimens. It is not applicable to products which experience dimensional changes during the test due to the loss of hydration water or which undergo other phase changes.
| Standards | Relationship |
| ISO 18099:2013 | Identical |
| ISO 29471:2008 | Thermal insulating products for building applications — Determination of dimensional stability under constant normal laboratory conditions (23 degrees C/50 % relative humidity) |
| EN 14706:2012 | Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature |
| EN 12085:2013 | Thermal insulating products for building applications - Determination of linear dimensions of test specimens |
| ISO 18096:2013 | Thermal insulating products for building equipment and industrial installations — Determination of maximum service temperature for preformed pipe insulation |
| EN 13468:2001 | Thermal insulating products for building equipment and industrial installations - Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH |
| ISO 12629:2011 | Thermal insulating products for building equipment and industrial installations — Determination of water vapour transmission properties of preformed pipe insulation |
| EN 1607:2013 | Thermal insulating products for building applications - Determination of tensile strength perpendicular to faces |
| EN 13820:2003 | Thermal insulating materials for building applications - Determination of organic content |
| EN 1608:2013 | Thermal insulating products for building applications - Determination of tensile strength parallel to faces |
| EN 13471:2001 | Thermal insulating products for building equipment and industrial installations - Determination of the coefficient of thermal expansion |
| ISO 29765:2008 | Thermal insulating products for building applications — Determination of tensile strength perpendicular to faces |
| ISO 29766:2008 | Thermal insulating products for building applications — Determination of tensile strength parallel to faces |
| ISO 29768:2008 | Thermal insulating products for building applications — Determination of linear dimensions of test specimens |
| ISO 18099:2013 | Thermal insulating products for building equipment and industrial installations — Determination of the coefficient of thermal expansion |
| EN 13469:2012 | Thermal insulating products for building equipment and industrial installations - Determination of water vapour transmission properties of preformed pipe insulation |
| EN 1605:2013 | Thermal insulating products for building applications - Determination of deformation under specified compressive load and temperature conditions |
| ISO 29472:2008 | Thermal insulating products for building applications — Determination of dimensional stability under specified temperature and humidity conditions |
| EN 824:2013 | Thermal insulating products for building applications - Determination of squareness |
| EN 825:2013 | Thermal insulating products for building applications - Determination of flatness |
| ISO 29767:2008 | Thermal insulating products for building applications Determination of short-term water absorption by partial immersion |
| EN 823:2013 | Thermal insulating products for building applications - Determination of thickness |
| EN 12431:2013 | Thermal insulating products for building applications - Determination of thickness for floating floor insulating products |
| EN 13470:2001 | Thermal insulating products for building equipment and industrial installations - Determination of the apparent density of preformed pipe insulation |
| ISO 12968:2010 | Thermal insulation products for building applications Determination of the pull-off resistance of external thermal insulation composite systems (ETICS) (foam block test) |
| ISO 12623:2011 | Thermal insulating products for building equipment and industrial installations — Determination of short-term water absorption by partial immersion of preformed pipe insulation |
| EN 1602:2013 | Thermal insulating products for building applications - Determination of the apparent density |
| ISO 29469:2008 | Thermal insulating products for building applications — Determination of compression behaviour |
| ISO 29769:2008 | Thermal insulating products for building applications — Determination of behaviour under point load |
| EN 13472:2012 | Thermal insulating products for building equipment and industrial installations - Determination of short term water absorption by partial immersion of preformed pipe insulation |
| EN 1603:2013 | Thermal insulating products for building applications - Determination of dimensional stability under constant normal laboratory conditions (23 °C/ 50 % relative humidity) |
| EN 1604:2013 | Thermal insulating products for building applications - Determination of dimensional stability under specified temperature and humidity conditions |
| ISO 29468:2008 | Thermal insulating products for building applications — Determination of flatness |
| ISO 12628:2011 | Thermal insulating products for building equipment and industrial installations — Determination of dimensions, squareness and linearity of preformed pipe insulation |
| ISO 29467:2008 | Thermal insulating products for building applications — Determination of squareness |
| ISO 29764:2008 | Thermal insulating products for building applications — Determination of deformation under specified compressive load and temperature conditions |
| EN 14707:2012 | Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature for preformed pipe insulation |
| EN 12089:2013 | Thermal insulating products for building applications - Determination of bending behaviour |
| ISO 29803:2010 | Thermal insulation products for building applications Determination of the resistance to impact of external thermal insulation composite systems (ETICS) |
| ISO 18097:2013 | Thermal insulating products for building equipment and industrial installations — Determination of maximum service temperature |
| EN 13495:2002 | Thermal insulation products for building applications - Determination of the pull-off resistance of external thermal insulation composite systems (ETICS)(foam block test) |
| ISO 12344:2010 | Thermal insulating products for building applications Determination of bending behaviour |
| ISO 29465:2008 | Thermal insulating products for building applications — Determination of length and width |
| EN 12430:2013 | Thermal insulating products for building applications - Determination of behaviour under point load |
| ISO 29466:2008 | Thermal insulating products for building applications — Determination of thickness |
| ISO 29770:2008 | Thermal insulating products for building applications — Determination of thickness for floating-floor insulating products |
| ISO 12624:2011 | Thermal insulating products for building equipment and industrial installations — Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH |
| EN 1609:2013 | Thermal insulating products for building applications - Determination of short term water absorption by partial immersion |
| EN 826:2013 | Thermal insulating products for building applications - Determination of compression behaviour |
| ISO 18098:2013 | Thermal insulating products for building equipment and industrial installations — Determination of the apparent density of preformed pipe insulation |
| ISO 29771:2008 | Thermal insulating materials for building applications — Determination of organic content |
| EN 13497:2002 | Thermal insulation products for building applications - Determination of the resistance to impact of external thermal insulation composite systems (ETICS) |
| ISO 29470:2008 | Thermal insulating products for building applications Determination of the apparent density |
| EN 822:2013 | Thermal insulating products for building applications - Determination of length and width |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.