BS ISO 2580-2 : 94 AMD 10660

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

PLASTICS - ACRYLONITRILE/BUTADIENE/STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES

Available format(s):

Superseded date: 15-03-2000

Language(s):

Published date: 23-11-2012

Publisher: British Standards Institution

Table of Contents - (Show below) - (Hide below)

NO CONTENTS SECTION

Abstract - (Show below) - (Hide below)

Specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of ABS moulding and extrusion materials. Coverage includes: treatment of the material before moulding; injection moulding; compression moulding; determination of properties. Also gives tables. BS AMD 10660 RENUMBERS STANDARD

General Product Information - (Show below) - (Hide below)

Committee	PRI/33
Development Note	Renumbered and superseded by BS EN ISO 2580-2 Supersedes BS 4935(1989) (04/2004)
Document Type	Standard
ISBN
Pages
Published
Publisher	British Standards Institution
Status	Superseded
Superseded By	BS EN ISO 2580-2:2003
Supersedes	BS 4935:1989

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
ISO 2580-2:2003	Identical

Standards Referencing This Book - (Show below) - (Hide below)

IEC 60243-1:2013	Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60112:2003+AMD1:2009 CSV	Method for the determination of the proof and the comparative tracking indices of solid insulating materials
ISO 4589-3:2017	Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test
ISO 75-1:2013	Plastics Determination of temperature of deflection under load Part 1: General test method
ISO 1656:2014	Rubber, raw natural, and rubber latex, natural Determination of nitrogen content
ISO 293:2004	Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 3167:2014	Plastics Multipurpose test specimens
IEC 60250:1969	Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
ISO 4581:1994	Plastics Styrene/acrylonitrile copolymers Determination of residual acrylonitrile monomer content Gas chromatography method
ISO 294:1995	Plastics Injection moulding of test specimens of thermoplastic materials
ISO 8256:2004	Plastics — Determination of tensile-impact strength
ISO 10350:1993	Plastics Acquisition and presentation of comparable single-point data
ISO 75-2:2013	Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 527-2:2012	Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 1183:1987	Plastics Methods for determining the density and relative density of non-cellular plastics
IEC 60296:2012 RLV	Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
IEC 60093:1980	Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
ISO 180:2000	Plastics Determination of Izod impact strength
ISO 1210:1992	Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source
ISO 2561:2012	Plastics — Determination of residual styrene monomer in polystyrene (PS) and impact-resistant polystyrene (PS-I) by gas chromatography
ISO 291:2008	Plastics Standard atmospheres for conditioning and testing
ISO 62:2008	Plastics Determination of water absorption
ISO 306:2013	Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 4589-2:2017	Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
ISO 179:1993	Plastics Determination of Charpy impact strength
ISO 2818:1994	Plastics — Preparation of test specimens by machining
ISO 899-1:2017	Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 2580-1:2002	Plastics Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 178:2010	Plastics Determination of flexural properties
ISO 1133:2005	Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
IEC 61006:2004	Electrical insulating materials - Methods of test for the determination of the glass transition temperature
ISO 527-1:2012	Plastics Determination of tensile properties Part 1: General principles

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart