BS ISO 4156-3:2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Straight cylindrical involute splines. Metric module, side fit Inspection
Hardcopy , PDF
03-02-2021
English
23-01-2006
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Reference conditions
6 Quality features
6.1 General
6.2 Size
6.3 Location
6.4 Form
7 Methods of inspection
7.1 Size
7.2 Location
7.3 Form
8 Measurements with balls or pins
8.1 General
8.2 Selection of balls or pins
8.3 Use and marking of pins
8.4 Statistical actual tolerance limit STA
8.5 Calculation of ball or pin diameter (D[Re] or D[Ri])
8.6 Calculation of dimensions for ball or pin
inspection (part and gauge inspection)
9 Measurement over k teeth - External splines (W)
9.1 Calculation of W
9.2 Choice of k
10 Gauges
10.1 Generalities
10.2 Length of measuring part of gauges
10.3 Manufacturing tolerances for spline
gauges
10.4 Values of deviation allowances of spline gauges
10.5 Inspection of gauges
10.6 Dimensions, designation and marking of gauges
11 Measurement of spline deviations
11.1 General
11.2 Total profile deviation F[alpha]
11.3 Total cumulative pitch deviation F[p]
11.4 Total helix deviation F[beta]
Annex A (informative) Influences of eccentricity and pitch
deviation as explained in
ISO 4156:1981
Gives data and guidance for the inspection of straight (non-helical) side fitting cylindrical involute splines.
| Committee |
MCE/5
|
| DevelopmentNote |
Supersedes 02/706432 DC (02/2006) Reviewed and confirmed by BSI, August 2015. (07/2015)
|
| DocumentType |
Standard
|
| Pages |
54
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 4156-3:2005 | Identical |
| ISO 5459:2011 | Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems |
| ISO 1328-2:1997 | Cylindrical gears ISO system of accuracy Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 1328-1:2013 | Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 4156-2:2005 | Straight cylindrical involute splines Metric module, side fit Part 2: Dimensions |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| ISO 4156-1:2005 | Straight cylindrical involute splines Metric module, side fit Part 1: Generalities |
| ISO/R 1938:1971 | ISO system of limits and fits Part II : Inspection of plain workpieces |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.