ISO 17484-1:2014
|
Plastics piping systems Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) Part 1: Specifications for systems |
ISO 13953:2001
|
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
EN 12106:1997
|
Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off |
ISO 1167-2:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
ISO 6964:1986
|
Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification |
ISO 8085-3:2001
|
Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels Metric series Specifications Part 3: Electrofusion fittings |
ISO 161-1:1996
|
Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series |
ISO 9080:2012
|
Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
ISO 13477:2008
|
Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
ISO 3:1973
|
Preferred numbers Series of preferred numbers |
ISO 18553:2002
|
Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds |
ISO/TS 10839:2000
|
Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation |
ISO 13479:2009
|
Polyolefin pipes for the conveyance of fluids Determination of resistance to crack propagation Test method for slow crack growth on notched pipes |
ISO 11414:2009
|
Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
ISO 12162:2009
|
Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient |
ISO 6259-1:2015
|
Thermoplastics pipes Determination of tensile properties Part 1: General test method |
ISO 13478:2007
|
Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST) |
ISO 3126:2005
|
Plastics piping systems Plastics components Determination of dimensions |
ISO 11922-1:1997
|
Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
ISO 16871:2003
|
Plastics piping and ducting systems — Plastics pipes and fittings — Method for exposure to direct (natural) weathering |
ISO 13954:1997
|
Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
ISO 15512:2016
|
Plastics Determination of water content |
ISO 11357-6:2008
|
Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
ISO 4065:1996
|
Thermoplastics pipes Universal wall thickness table |
ISO 497:1973
|
Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
ISO 13480:1997
|
Polyethylene pipes Resistance to slow crack growth Cone test method |
CEN/TS 1555-7:2013
|
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
ISO 6259-3:2015
|
Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes |
ISO 11413:2008
|
Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting |
ISO 1133:2005
|
Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
EN 12099:1997
|
Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
ISO 1167-1:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
ISO 2505:2005
|
Thermoplastics pipes — Longitudinal reversion — Test method and parameters |