BS ISO 6402-2 : 94 AMD 10652
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
23-11-2012
15-11-1999
NO CONTENTS SECTION
Specifies the methods of preparation of test specimens and test methods to be used in determining the properties of ASA, AES, ACS moulding and extrusion materials. Lists properties and test methods which are suitable and necessary to characterise ASA, AES, ACS moulding and extrusion materials. BS AMD 10652 RENUMBERS STD
| Committee |
PRI/33
|
| DevelopmentNote |
Renumbered and superseded by BS EN ISO 6402-2 (02/2004)
|
| DocumentType |
Standard
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 6402-2:2003 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 75-1:2013 | Plastics — Determination of temperature of deflection under load — Part 1: General test method |
| ISO 1656:2014 | Rubber, raw natural, and rubber latex, natural — Determination of nitrogen content |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics — Multipurpose test specimens |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 6402-1:2002 | Plastics — Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 294:1995 | Plastics — Injection moulding of test specimens of thermoplastic materials |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 4851:1979 | Personal eye-protectors — Ultra-violet filters — Utilisation and transmittance requirements |
| ISO 10350:1993 | Plastics — Acquisition and presentation of comparable single-point data |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 1183:1987 | Plastics — Methods for determining the density and relative density of non-cellular plastics |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 180:2000 | Plastics — Determination of Izod impact strength |
| ISO 1210:1992 | Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source |
| ISO 2561:2012 | Plastics — Determination of residual styrene monomer in polystyrene (PS) and impact-resistant polystyrene (PS-I) by gas chromatography |
| ISO 291:2008 | Plastics — Standard atmospheres for conditioning and testing |
| ISO 62:2008 | Plastics — Determination of water absorption |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 179:1993 | Plastics — Determination of Charpy impact strength |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| IEC 61006:2004 | Electrical insulating materials - Methods of test for the determination of the glass transition temperature |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.