Skip to content
Please enter a keyword to search

  • BS ISO 7391-2 : 1996 AMD 10746

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES

    Available format(s): 

    Superseded date:  15-07-2000

    Language(s): 

    Published date:  23-11-2012

    Publisher:  British Standards Institution

    Sorry this product is not available in your region.

    Add To Cart

    Abstract - (Show below) - (Hide below)

    Defines methods for preparing test specimens and methods of testing for use in determination of the properties of polycarbonabte moulding and extrusion materials. Also states requirements for handling test material and conditioning both test material prior to moulding and specimens prior to testing.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/82
    Development Note Superseded and renumbered by BS EN ISO 7391-2 (06/2000) Supersedes 95/123277 DC (06/2005)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
    IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
    ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
    EN ISO 62:2008 Plastics - Determination of water absorption (ISO 62:2008)
    EN ISO 10350 : 1995 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA
    ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
    ISO 3167:2014 Plastics Multipurpose test specimens
    EN ISO 180:2000/A2:2013 PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013)
    IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
    EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
    EN ISO 75-1:2013 Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO 75-1:2013)
    EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
    ISO 10350:1993 Plastics Acquisition and presentation of comparable single-point data
    EN ISO 2818:1996 PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING
    EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
    ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
    EN ISO 7391-1:2006 Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 7391-1:2006)
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
    ISO 1183:1987 Plastics Methods for determining the density and relative density of non-cellular plastics
    IEC 60296:2012 RLV Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
    EN ISO 3167:2014 Plastics - Multipurpose test specimens (ISO 3167:2014)
    IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
    ISO 180:2000 Plastics Determination of Izod impact strength
    ISO 1210:1992 Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source
    EN ISO 179 : 1996 PLASTICS - DETERMINATION OF CHARPY IMPACT STRENGTH
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    EN ISO 4589-2:2017 Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test (ISO 4589-2:2017)
    ISO 62:2008 Plastics Determination of water absorption
    ISO 7391-1:2006 Plastics Polycarbonate (PC) moulding and extrusion materials Part 1: Designation system and basis for specifications
    ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
    EN ISO 291:2008 Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008)
    ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
    ISO 4589-2:2017 Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
    ISO 179:1993 Plastics Determination of Charpy impact strength
    ISO 2818:1994 Plastics — Preparation of test specimens by machining
    ISO 1628-4:1999 Plastics — Determination of the viscosity of polymers in dilute solution using capillary viscometers — Part 4: Polycarbonate (PC) moulding and extrusion materials
    ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
    EN ISO 1133:2005 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
    ISO 178:2010 Plastics Determination of flexural properties
    EN ISO 306:2013 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013)
    ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
    IEC 61006:2004 Electrical insulating materials - Methods of test for the determination of the glass transition temperature
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    EN ISO 294-1:2017 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective