BS QC 960000:1992
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Generic specification
Hardcopy , PDF
28-02-2010
English
15-10-1992
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Committees responsible
National foreword
Introduction
Section 1. Scope and object
1.1 Scope
1.2 Object
Section 2. General
2.1 Related publications
2.2 Units and symbols
2.3 Terminology
2.4 Preferred values
2.5 Marking
Section 3. Quality assessment procedures
3.1 Qualification approval/Quality assessment systems
3.2 Primary stage of manufacture
3.3 Structurally similar switches
3.4 Qualification approval procedures
3.5 Quality conformance inspection
3.6 Alternative test methods
3.7 Unchecked parameters
Section 4. Test and measurement procedures
4.1 General
4.2 Standard atmospheric conditions
4.3 General examination
4.4 Resistance measurements
4.5 Voltage stress
4.6 Temperature rise
4.7 Dynamic stress
4.8 Mechanical strength
4.9 Mechanical endurance
4.10 Electrical endurance
4.11 Overload
4.12 Environmental
4.13 Soldering
4.14 Panel seal
4.15 Enclosure seal
4.16 Fluid resistance
4.17 Fire hazard
4.18 Capacitance
4.19 Illumination
Figures
1. Contact bounce test circuit
2. Typical trace of contact bounce
3. Application of forces and torques for test 4.8.1
4. Submersion seal test enclosure
Establishes a uniform quality assessment system and provides consistency by specifying terminology, symbols, test methods and other necessary information.
| Committee |
EPL/48
|
| DevelopmentNote |
Supersedes 84/20971 DC (08/2005)
|
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| BS QC 960401:1992 | Specification for harmonized system of quality assessment for electronic components. Blank detail specification: electromechanical switches for use in electronic equipment. Blank detail specification for pushbutton switches |
| BS QC 960100:1992 | Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for rotary switches |
| BS QC 960200:1992 | Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for lever (toggle) switches |
| BS QC 960400:1992 | Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for pushbutton switches |
| BS QC 960301:1992 | Specification for harmonized system of quality assessment for electronic components. Blank detail specification: electromechanical switches for use in electronic equipment. Blank detail specification for sensitive switches |
| BS QC 960201:1992 | Specification for harmonized system of quality assessment for electronic components. Blank detail specification: electromechanical switches for use in electronic equipment. Blank detail specification for lever (toggle) switches |
| BS QC 960300:1992 | Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for sensitive switches |
| BS QC 960500:1992 | Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for in-line package switches |
| BS 5772-8:1985 | Specification for electromechanical components for electronic equipment: basic testing procedures and measuring methods Connector tests (mechanical) and mechanical tests on contacts and terminations |
| BS 4500-1.1(1990) : AMD 7630 | ISO LIMITS AND FITS - GENERAL, TOLERANCES AND DEVIATIONS - SPECIFICATION FOR BASES OF TOLERANCES, DEVIATIONS AND FITS |
| BS 5772-4:1979 | Specification for electromechanical components for electronic equipment: basic testing procedures and measuring methods Dynamic stress tests |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| BS 6001-1:1991 | Sampling procedures for inspection by attributes Specification for sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection |
| IEC 60512-7:1993 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 7: Mechanical operating tests and sealing tests |
| BS 2011-2.1XA(1981) : 1981 AMD 7553 | ENVIRONMENTAL TESTING - TESTS - TEST XA AND GUIDANCE - IMMERSION IN CLEANING SOLVENTS |
| BS 4727-1:GRP13(1991) : 1991 | GLOSSARY OF ELECTROTECHNICAL, POWER, TELECOMMUNICATION, ELECTRONICS, LIGHTING AND COLOUR TERMS - TERMS COMMON TO POWER, TELECOMMUNICATIONS AND ELECTRONICS - ELECTROMECHANICAL COMPONENTS FOR ELECTRONIC EQUIPMENT |
| BS 4727-2:GRP06(1985) : 1985 | GLOSSARY OF ELECTROTECHNICAL POWER TELECOMMUNICATION ELECTRONICS LIGHTING AND COLOUR TERMS - TERMS PARTICULAR TO POWER ENGINEERING - SWITCHGEAR & CONTROLGEAR TERMINOLOGY INCLUDING FUSE TERMINOLOGY |
| BS 2011-2.1Z/AD:1977 | Environmental testing. Tests Tests Z/AD. Composite temperature/humidity cyclic test |
| IEC 60068-2-38:2009 | Environmental testing - Part 2-38: Tests - Test Z/AD: Composite temperature/humidity cyclic test |
| BS 6334:1983 | Methods of test for the determination of the flammability of solid electrical insulating materials when exposed to an igniting source |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| BS QC 001002:1991 | Rules of procedure of the IEC quality assessment system for electronic components (IECQ) |
| BS 5555:1981 | Specification for SI units and recommendations for the use of their multiples and of certain other units |
| BS 5772-3:1979 | Specification for electromechanical components for electronic equipment: basic testing procedures and measuring methods Current-carrying capacity tests |
| PD 6499:1981 | Guide to insulation co-ordination within low-voltage systems including clearances and creepage distances for equipment |
| BS 2011-2.1T:1981 | Environmental testing. Tests Test T. Soldering |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.