CAN/CSA-ISO/IEC/IEEE 18881:18 (R2022)

1. Overview
2. Normative references
3. Definitions, acronyms, and abbreviations
4. Architecture
5. Management and control unit (MCU)
6. Gateway (GW)
7. Gateway (GW) control and management
8. SERVICE protocol
9. WRITE, FETCH, and TRAP protocol extension
10. Compatibilities with IEEE Std 1888-2011
11. Security considerations
Annex A (informative) - A typical process of the service
        provided by the MCU
Annex B (informative) - Recommended component model
        for component management
Annex C (informative) - Access control list encoding
Annex D (informative) - Procedures to provide the ACL
        from the MCU to the components
Annex E (informative) - Importing an SNMP management
        information base
Annex F (informative) - Bibliography

Standards development within the Information Technology sector is harmonized with international standards development. Through the CSA Technical Committee on Information Technology (TCIT), Canadians serve as the SCC Mirror Committee (SMC) on ISO/IEC Joint Technical Committee 1 on Information Technology (ISO/IEC JTC1) for the Standards Council of Canada (SCC), the ISO member body for Canada and sponsor of the Canadian National Committee of the IEC. Also, as a member of the International Telecommunication Union (ITU), Canada participates in the International Telegraph and Telephone Consultative Committee (ITU-T). Scope Based on the IEEE 1888™ protocols, this standard describes network gateway central access control and management policy through the extension of existing interface protocols, message formats, and interactive processing in ubiquitous green community control networks (UGCCNets). This Standard extends the definition of the original interface protocols and message formats and mainly specifies the network gateway signal flow for access control, registration management, state querying, event reporting, remote management, etc. 1.2 Purpose This Standard aims to provide open and standardized network gateway management interface protocols for service providers, system integrators, equipment manufacturers, etc., through the extension of the original interface protocol in order to be able to remotely control and monitor the network gateway and other facilities in green communities, such as heating, ventilation, and air conditioning (HVAC); lighting systems; energy equipment; and so on.

CSA Preface Standards development within the Information Technology sector is harmonized with international standards development. Through the CSA Technical Committee on Information Technology (TCIT), Canadians serve as the SCC Mirror Committee (SMC) on ISO/IEC Joint Technical Committee 1 on Information Technology (ISO/IEC JTC1) for the Standards Council of Canada (SCC), the ISO member body for Canada and sponsor of the Canadian National Committee of the IEC. Also, as a member of the International Telecommunication Union (ITU), Canada participates in the International Telegraph and Telephone Consultative Committee (ITU-T). For brevity, this Standard will be referred to as “CAN/CSA-ISO/IEC/IEEE 18881” throughout. At the time of publication, ISO/IEC/IEEE 18881:2016 is available from ISO and IEC in English only. CSA Group will publish the French version when it becomes available from ISO and IEC. This Standard was reviewed by the CSA TCIT under the jurisdiction of the CSA Strategic Steering Committee on Information and Communications Technology and deemed acceptable for use in Canada. From time to time, ISO/IEC may publish addenda, corrigenda, etc. The TCIT will review these documents for approval and publication. For a listing, refer to the Current Standards Activities page at standardsactivities.csa.ca. This Standard has been formally approved, without modification, by the Technical Committee and has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. 1.1 Scope Based on the IEEE 1888™ protocols, this standard describes network gateway central access control and management policy through the extension of existing interface protocols, message formats, and interactive processing in ubiquitous green community control networks (UGCCNets). This Standard extends the definition of the original interface protocols and message formats and mainly specifies the network gateway signal flow for access control, registration management, state querying, event reporting, remote management, etc. 1.2 Purpose This Standard aims to provide open and standardized network gateway management interface protocols for service providers, system integrators, equipment manufacturers, etc., through the extension of the original interface protocol in order to be able to remotely control and monitor the network gateway and other facilities in green communities, such as heating, ventilation, and air conditioning (HVAC); lighting systems; energy equipment; and so on.