• CEI EN 60871-1 : 2015

    Current The latest, up-to-date edition.

    SHUNT CAPACITORS FOR A.C. POWER SYSTEMS HAVING A RATED VOLTAGE ABOVE 1000 V - PART 1: GENERAL

    Available format(s):  Hardcopy, PDF

    Language(s):  English, English - Italian

    Published date:  01-01-2015

    Publisher:  Comitato Elettrotecnico Italiano

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1. SCOPE
    2. Normative references
    3. Terms and definitions
    4. Service conditions
    5. Quality requirements and tests
    6. Classification of tests
    7. Capacitance measurement (routine test)
    8. Measurement of the tangent of the loss angle
        (tan [delta]) of the capacitor (routine test)
    9. Voltage test between terminals (routine test)
    10. AC voltage test between terminals and
        container (routine test)
    11. Test of internal discharge device (routine test)
    12. Sealing test (routine test)
    13. Thermal stability test (type test)
    14. Measurement of the tangent of the loss angle
        (tan [delta]) of the capacitor at elevated
        temperature (type test)
    15. AC voltage test between terminals and
        container (type test)
    16. Lightning impulse test between terminals and
        container (type test)
    17. Short-circuit discharge test (type test)
    18. Insulation levels
    19. Overloads - Maximum permissible voltage
    20. Overloads - Maximum permissible current
    21. Safety requirements for discharge devices
    22. Safety requirements for container connections
    23. Safety requirements for protection of the environment
    24. Other safety requirements
    25. Markings of the capacitor unit
    26. Markings of the capacitor bank
    27. Guide for installation and operation
    Annex A (normative) - Precautions to be taken to
                          avoid pollution of the environment by
                          polychlorinated biphenyls
    Annex B (normative) - Additional definitions,
                          requirements and tests for power filter
                          Capacitors
    Annex C (normative) - Test requirements and
                          application guide for external fuses and
                          units to be externally fused
    Annex D (informative) - Formulae for capacitors and
                            installations
    Annex E (informative) - Capacitor bank fusing and unit
                            arrangement
    Bibliography
    Annex ZA (normative) - Normative references to
                           international publications
                           with their corresponding
                           European publications

    Abstract - (Show below) - (Hide below)

    Describes the capacitor units and capacitor banks intended to be used, particularly, for power-factor correction of a.c. power systems having a rated voltage above 1000 V and frequencies of 15 Hz to 60 Hz.

    General Product Information - (Show below) - (Hide below)

    Committee CT 33
    Development Note Classificazione CEI 33-18 (09/2001) Partially supersedes CEI 33-7 (05/2004)
    Document Type Standard
    Publisher Comitato Elettrotecnico Italiano
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60871-4:2014 Shunt capacitors for AC power systems having a rated voltage above 1 000 V - Part 4: Internal fuses
    IEC 61048:2006+AMD1:2015 CSV Auxiliaries for lamps - Capacitors for use in tubular fluorescent and other discharge lamp circuits - General and safety requirements
    HD 588.1 : S1 AMD 1 HIGH VOLTAGE TEST TECHNIQUES - GENERAL DEFINITIONS AND TEST REQUIREMENTS
    IEC 60549:2013 High-voltage fuses for the external protection of shunt capacitors
    IEEE 1036 : 2010 GUIDE FOR APPLICATION OF SHUNT POWER CAPACITORS
    IEC 61049:1991 Capacitors for use in tubular fluorescent and other discharge lamp circuits. Performance requirements
    IEC 61270-1:1996 Capacitors for microwave ovens - Part 1: General
    IEC 60273:1990 Characteristic of indoor and outdoor post insulators for systems with nominal voltages greater than 1000 V
    EN 60071-1:2006/A1:2010 INSULATION CO-ORDINATION - PART 1: DEFINITIONS, PRINCIPLES AND RULES
    IEC 60931-3:1996 Shunt capacitors of the non-self-healing type for AC power systems having a rated voltage up to and including 1000 V - Part 3: Internal fuses
    IEC 60071-2:1996 Insulation co-ordination - Part 2: Application guide
    IEC 60050-436:1990 International Electrotechnical Vocabulary (IEV) - Part 436: Power capacitors
    EN 60071-2 : 1997 INSULATION CO-ORDINATION - APPLICATION GUIDE
    IEC 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
    IEC 60071-1:2006+AMD1:2010 CSV Insulation co-ordination - Part 1: Definitions, principles and rules
    CEI 42-4 : 1997 TECNICHE DI PROVA AD ALTA TENSIONE - PARTE 1: DEFINIZIONI E PRESCRIZIONI GENERALI RELATIVE ALLE PROVE
    EN 60871-4:2014 SHUNT CAPACITORS FOR AC POWER SYSTEMS HAVING A RATED VOLTAGE ABOVE 1000 V - PART 4: INTERNAL FUSES (IEC 60871-4:2014)
    IEEE 18 : 2012 SHUNT POWER CAPACITORS
    IEC 60110-1:1998 Power capacitors for induction heating installations - Part 1: General
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective