• CEI EN 60917-2-3 : 2007

    Current The latest, up-to-date edition.

    MODULAR ORDER FOR THE DEVELOPMENT OF MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT PRACTICES - PART 2-3: SECTIONAL SPECIFICATION - INTERFACE CO-ORDINATION DIMENSIONS FOR THE 25 MM EQUIPMENT PRACTICE - EXTENDED DETAIL SPECIFICATION - DIMENSIONS FOR SUBRACKS, CHASSIS, BACKPLANES, FRONT PANELS AND PLUG-IN UNITS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2007

    Publisher:  Comitato Elettrotecnico Italiano

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1. Scope and object
    2. Normative references
    3. Terms and definitions
    4. Arrangement overview
    5. Subrack dimensions for injector/extractor
        handle of plug-in units
    6. Dimensions of injector/extractor handle for
        plug-in units
    7. Subrack and plug-in units with electromagnetic
        shielding provision
    8. Key/coding system for subrack and plug-in units
    9. Alignment pin and/or electrical contact for front
        panels and plug-in units
    10. Electrostatic discharge provision for plug-in
        units and subracks
    11. Subrack dimensions for rear-mounted
        plug-in units
    Annex A (Informative) - Subrack, plug-in unit and
                            backplane dimensions for using
                            metric connectors
    Annex ZA (normative) - Normative references to
                           international publications
                           with their corresponding
                           European publications

    Abstract - (Show below) - (Hide below)

    Gives additional dimensions for a modular range of subracks and associated plug-in units based on IEC 60917-2-2.

    General Product Information - (Show below) - (Hide below)

    Committee CT 48
    Document Type Standard
    Publisher Comitato Elettrotecnico Italiano
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 60917-2-2 : 1996 MODULAR ORDER FOR THE DEVELOPMENT OF MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT PRACTICES - SECTIONAL SPECIFICATION - INTERFACE CO-ORDINATION DIMENSIONS FOR THE 25 MM EQUIPMENT PRACTICE - DETAIL SPECIFICATION - DIMENSIONS FOR SUBRACKS, CHASSIS, BACKPLANES, FRONT PANELS AND PLUG-IN UNITS
    EN 61076-4-104 : 1999 CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4-104: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART MODULAR CONNECTORS, BASIC GRID OF 2.0 MM WITH TERMINATIONS ON A MULTIPLE GRID OF 0.5 MM
    IEC 61076-4-100:2001 Connectors for electronic equipment - Part 4-100: Printed board connectors with assessed quality - Detail specification for two-part connector modules having a grid of 2,5 mm for printed boards and backplanes
    IEC 61076-4-104:1999 Connectors for use in d.c., low frequency analogue and digital high speed data applications - Part 4-104: Printed board connectors with assessed quality - Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm
    IEC 60917-2-1:1993 Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Section 1: Detail specification - Dimensions for cabinets and racks
    EN 61076-4-100 : 2001 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-100: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES HAVING A GRID OF 2.5 MM FOR PRINTED BOARDS AND BACKPLANES
    EN 61076-4-101 : 2001 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-101: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES, HAVING A BASIC GRID OF 2,0 MM FOR PRINTED BOARDS AND BACKPLANES IN ACCORDANCE WITH IEC 60917 (IEC 61076-4-101:2001)
    IEC 60917-2-2:1994 Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co-ordination dimensions for the 25 mm equipment practice - Section 2: Detail specification - Dimensions for subracks, chassis, backplanes, front panels and plug-in units
    IEC 61076-4-101:2001 Connectors for electronic equipment - Part 4-101: Printed board connectors with assessed quality - Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917
    EN 60917-2-1 : 1995 MODULAR ORDER FOR THE DEVELOPMENT OF MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT PRACTICES - PART 2: SECTIONAL SPECIFICATION - INTERFACE CO-ORDINATION DIMENSIONS FOR THE 25 MM EQUIPMENT PRACTICE - SECTION 1: DETAIL SPECIFICATION - DIMENSIONS FOR CABINETS AND RACKS
    IEC 60917-1:1998+AMD1:2000 CSV Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective