ISO 3744:2010
|
Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
CEI 29-4 : 1ED 1968
|
FILTRI DI BANDA DI OTTAVA, DI MEZZA OTTAVA E DI TERZI DI OTTAVA PER ANALISI ACUSTICHE |
IEC 60068-2-63:1991
|
Environmental testing - Part 2: Test methods - Test Eg: Impact, spring hammer. |
IEC 60050-151:2001
|
International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
IEC 60227-3:1993+AMD1:1997 CSV
|
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 3: Non-sheathed cables for fixed wiring |
CEI 48-4 : 1ED 1983
|
|
IEC 60068-2-11:1981
|
Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
ISO 3740:2000
|
Acoustics Determination of sound power levels of noise sources Guidelines for the use of basic standards |
IEC 60603-11:1992
|
Connectors for frequencies below 3 MHz for use with printed boards - Part 11: Detail specification for concentric connectors (dimensions for free connectors and fixed connectors) |
CEI 20-20/3 : 1996
|
CAVI ISOLATI CON POLIVINILCLORURO CON TENSIONE NOMINALE NON SUPERIORE A 450/750 V - PARTE 3: CAVI SENZA GUAINA PER POSA FISSA |
IEC 60096-0-1:2012+AMD1:2017 CSV
|
Radio frequency cables - Part 1- 0: Guide to the design of detail specifications - Coaxial cables |
CEI 48-15 : 1998
|
FLAT, QUICK-CONNECT TERMINATIONS |
CEI 46-17 : 1998
|
RADIO-FREQUENCY CABLES - PART 0: GUIDE TO THE DESIGN OF DETAIL SPECIFICATIONS - SECTION 1: COAXIAL CABLES |
Q C 001005 : 1995
|
REGISTER OF FIRMS, PRODUCTS AND SERVICES APPROVED UNDER THE IECQ SYSTEM, INCLUDING ISO 900 |
IEC 60999-1:1999
|
Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included) |
IEC 60352-1:1997
|
Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance |
ISO 3746:2010
|
Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
IEC 60068-2-3:1969
|
Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state |
IEC 60225:1966
|
Octave, half-octave and third-octave band filters intended for the analysis of sounds and vibrations |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV
|
Degrees of protection provided by enclosures (IP Code) |
IEC 60352-5:2012
|
Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance |
CEI 70-1 : 1980 COR 1993
|
|
IEC 60352-2:2006+AMD1:2013 CSV
|
Solderless connections - Part 2: Crimped connections - Generalrequirements, test methods and practical guidance |
IEC 60060-1:2010
|
High-voltage test techniques - Part 1: General definitions and test requirements |
ISO 3745:2012
|
Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
IEC 61010-2-031:1993
|
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-031: Particular requirements for hand-held probe assemblies for electrical measurement and test |
CEI 42-4 : 1997
|
TECNICHE DI PROVA AD ALTA TENSIONE - PARTE 1: DEFINIZIONI E PRESCRIZIONI GENERALI RELATIVE ALLE PROVE |
IEC 60068-2-14:2009
|
Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
IEC 60651:1979+AMD1:1993+AMD2:2000 CSV
|
Sound level meters |