• CEI EN 61347-2-2 : 2012

    Current The latest, up-to-date edition.

    LAMP CONTROLGEAR - PART 2-2: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC STEPDOWN CONVERTORS FOR FILAMENT LAMPS

    Available format(s):  Hardcopy, PDF

    Language(s):  English - Italian

    Published date:  01-01-2012

    Publisher:  Comitato Elettrotecnico Italiano

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General requirements
    5 General notes on tests
    6 Classification
    7 Marking
    8 Protection against accidental contact with live parts
    9 Terminals
    10 Provisions for protective earthing
    11 Moisture resistance and insulation
    12 Electric strength
    13 Thermal endurance test for windings of ballasts
    14 Fault conditions
    15 Transformer heating
    16 Construction
    17 Creepage distances and clearances
    18 Screws, current-carrying parts and connections
    19 Resistance to heat, fire and tracking
    20 Resistance to corrosion
    Annex A (normative) - Test to establish whether a conductive
            part is a live part which may cause an electric shock
    Annex B (normative) - Particular requirements for
            thermally protected lamp controlgear
    Annex C (normative) - Particular requirements for electronic
            lamp controlgear with means of protection against
            overheating
    Annex D (normative) - Requirements for carrying out the
            heating tests of thermally protected lamp controlgear
    Annex E (normative) - Use of constant S other than
            4500 in tw tests
    Annex F (normative) - Draught-proof enclosure
    Annex G (normative) - Explanation of the derivation of the
            values of pulse voltages
    Annex H (normative) - Tests
    Annex I (normative) - Particular additional requirements
            for SELV d.c. or a.c. supplied electronic step-down
            convertors for filament lamps
    Bibliography
    Annex ZA (normative) - Normative references to international
              publications with their corresponding European
              publications

    Abstract - (Show below) - (Hide below)

    Describes the electronic step-down convertors for use on d.c. supplies of up to 250 V or a.c. supplies of up to 1000 V, at 50 Hz or 60 Hz and with rated output voltage <= 50 V r.m.s. at a frequency deviating from the supply frequency, or 120 V ripple free d.c. between conductors and between any conductor and earth, associated with tungsten-halogen lamps as specified in IEC 60357 and other filament lamps.

    General Product Information - (Show below) - (Hide below)

    Committee CT 34
    Development Note Classificazione CEI 34-93. (01/2002) Supersedes CEI EN 61046. (02/2003) To be read in conjunction with CEI EN 61347-1. (07/2005)
    Document Type Standard
    Publisher Comitato Elettrotecnico Italiano
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    CEI 64-8/7 : 2012 LOW VOLTAGE ELECTRICAL INSTALLATIONS - PART 7: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61558-2-13:2009 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1100 V - PART 2-13: PARTICULAR REQUIREMENTS AND TESTS FOR AUTO TRANSFORMERS AND POWER SUPPLY UNITS INCORPORATING AUTO TRANSFORMERS
    IEC 61558-2-1:2007 SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 2-1: PARTICULAR REQUIREMENTS AND TESTS FOR SEPARATING TRANSFORMERS AND POWER SUPPLIES INCORPORATING SEPARATING TRANSFORMERS FOR GENERAL APPLICATIONS
    EN 61558-2-16:2009/A1:2013 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS (IEC 61558-2-16:2009/A1:2013)
    EN 61047 : 2004 DC or AC supplied electronic step-down convertors for filament lamps - Performance requirements
    EN 61558-2-13 : 2009 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1100 V - PART 2-13: PARTICULAR REQUIREMENTS AND TESTS FOR AUTO TRANSFORMERS AND POWER SUPPLY UNITS INCORPORATING AUTO TRANSFORMERS
    IEC 61558-2-16:2009+AMD1:2013 CSV Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units
    IEC 61347-1:2015 RLV Lamp controlgear - Part 1: General and safety requirements
    IEC 61047:2004 DC or AC supplied electronic step-down convertors for filament lamps - Performance requirements
    EN 60357:2003/A11:2016 TUNGSTEN HALOGEN LAMPS (NON-VEHICLE) - PERFORMANCE SPECIFICATIONS
    EN 61558-2-1 : 2007 SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 2-1: PARTICULAR REQUIREMENTS AND TESTS FOR SEPARATING TRANSFORMERS AND POWER SUPPLIES INCORPORATING SEPARATING TRANSFORMERS FOR GENERAL APPLICATIONS
    EN 61347-1 : 2015 LAMP CONTROLGEAR - PART 1: GENERAL AND SAFETY REQUIREMENTS (IEC 61347-1:2015)
    EN 61558-2-6 : 2009 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1100 V - PART 2-6: PARTICULAR REQUIREMENTS AND TESTS FOR SAFETY ISOLATING TRANSFORMERS AND POWER SUPPLY UNITS INCORPORATING SAFETY ISOLATING TRANSFORMERS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective