• CISPR 25:2016

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  16-12-2021

    Language(s): 

    Published date:  27-10-2016

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CISPR 25:2016 contains limits and procedures for the measurement of radio disturbances in the frequency range of 150 kHz to 2 500 MHz. The standard applies to any electronic/electrical component intended for use in vehicles, trailers and devices. Refer to International Telecommunications Union (ITU) publications for details of frequency allocations. The limits are intended to provide protection for receivers installed in a vehicle from disturbances produced by components/modules in the same vehicle. The method and limits for a complete vehicle (whether connected to the power mains for charging purposes or not) are in Clause 5 and the methods and limits for components/modules are in Clause 6. Only a complete vehicle test can be used to determine the component compatibility with respect to a vehicle's limit. The receiver types to be protected are, for example, broadcast receivers (sound and television), land mobile radio, radio telephone, amateur, citizens' radio, Satellite Navigation (GPS etc.), Wi-Fi and Bluetooth. For the purpose of this standard, a vehicle is a machine, which is self-propelled by an internal combustion engine, electric means, or both. Vehicles include (but are not limited to) passenger cars, trucks, agricultural tractors and snowmobiles. Annex A provides guidance in determining whether this standard is applicable to particular equipment. This fourth edition cancels and replaces the third edition published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
    - inclusion of charging mode for electric vehicles (EV) and plug-in electric vehicles (PHEV),
    - the methods for chamber validation have been included,
    - test methods for shielded power supply systems for high voltages for electric and hybrid electric vehicles have been included,
    - overall improvement.
    The contents of the corrigendum of October 2017 have been included in this copy.

    General Product Information - (Show below) - (Hide below)

    Committee CISPR/CIS/D
    Development Note Supersedes CISPR 21. (11/2008) Also available in CD-ROM format. Stability Date: 2018. (10/2016)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    SAE J 2716 : 2016 SENT - SINGLE EDGE NIBBLE TRANSMISSION FOR AUTOMOTIVE APPLICATIONS
    SAE J 551/1 : 2015 PERFORMANCE LEVELS AND METHODS OF MEASUREMENT OF ELECTROMAGNETIC COMPATIBILITY OF VEHICLES, BOATS (UP TO 15 M), AND MACHINES (16.6 HZ TO 18 GHZ)
    CSA CISPR 12:2010 VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF OFF-BOARD RECEIVERS
    16/30342956 DC : 0 BS CISPR 36 ED1.0 - ELECTRIC AND HYBRID ROAD VEHICLES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION
    SAE J 2284-2 : 2016 HIGH SPEED CAN (HSC) FOR VEHICLE APPLICATIONS AT 250 KBPS
    BS ISO 22902-7 : 2006 ROAD VEHICLES - AUTOMOTIVE MULTIMEDIA INTERFACE - PART 7: PHYSICAL SPECIFICATION
    12/30257420 DC : 0 BS EN 61851-23 ED 1.0 - ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 23: D.C. ELECTRIC VEHICLE CHARGING STATION
    SAE J 2284-4 : 2016 HIGH-SPEED CAN (HSC) FOR VEHICLE APPLICATIONS AT 500 KBPS WITH CAN FD DATA AT 2 MBPS
    BS EN 61967-1:2002 Integrated circuits. Measurement of electromagnetic emissions, 150 kHz to 1 GHz General conditions and definitions
    BS PD CISPR/TR 16-4-4 : 2007 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 4-4: UNCERTAINTIES, STATISTICS AND LIMIT MODELLING - STATISTICS OF COMPLAINTS AND A MODEL FOR THE CALCULATION OF LIMITS FOR THE PROTECTION OF RADIO SERVICES
    SAE J ISO 13766 : FEB 2003 EARTH-MOVING MACHINERY - ELECTROMAGNETIC COMPATIBILITY
    SAE J 2561 : 2016 BLUETOOTH[TM] WIRELESS PROTOCOL FOR AUTOMOTIVE APPLICATIONS
    PREN 15194 : DRAFT 2015 CYCLES - ELECTRICALLY POWER ASSISTED CYCLES - EPAC BICYCLES
    SAE J 2602 : 2010 LIN NETWORK FOR VEHICLE APPLICATIONS
    17/30358367 DC : 0 BS EN 17128 - NON-APPROVED LIGHT MOTORIZED VEHICLES FOR THE TRANSPORTATION OF PERSONS AND GOODS AND RELATED FACILITIES - PERSONAL LIGHT ELECTRIC VEHICLES (PLEV) - SAFETY REQUIREMENTS AND TEST METHODS
    IEC 60810:2017 Lamps, light sources and LED packages for road vehicles - Performance requirements
    SAE J 2697 : 2017 INVERTER REQUIREMENTS FOR CLASS EIGHT TRUCKS - TRUCK AND BUS
    01/714099 DC : DRAFT OCT 2001 ISO 16750-2 - ROAD VEHICLES - ENVIRONMENTAL CONDITIONS AND TESTING FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PART 2: ELECTRICAL LOADS
    BS ISO 16750-2 : 2012 ROAD VEHICLES - ENVIRONMENTAL CONDITIONS AND TESTING FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PART 2: ELECTRICAL LOADS
    05/30116652 DC : DRAFT MAY 2005 ISO 16750-2 - ROAD VEHICLES - ENVIRONMENTAL CONDITIONS AND TESTING FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PART 2: ELECTRICAL LOADS
    08/30173378 DC : DRAFT AUG 2008 BS ISO 16750-2 - ROAD VEHICLES - ENVIRONMENTAL CONDITIONS AND TESTING FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PART 2: ELECTRICAL LOADS
    EN 13309:2010 Construction machinery - Electromagnetic compatibility of machines with internal power supply
    EN 60810 : 2018 LAMPS, LIGHT SOURCES AND LED PACKAGES FOR ROAD VEHICLES - PERFORMANCE REQUIREMENTS
    EN 61000-4-20:2010 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-20: TESTING AND MEASUREMENT TECHNIQUES - EMISSION AND IMMUNITY TESTING IN TRANSVERSE ELECTROMAGNETIC (TEM) WAVEGUIDES
    EN 60601-1-2:2015 MEDICAL ELECTRICAL EQUIPMENT - PART 1-2: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE - COLLATERAL STANDARD: ELECTROMAGNETIC DISTURBANCES - REQUIREMENTS AND TESTS (IEC 60601-1-2:2014)
    EN 61967-1 : 2002 INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC EMISSIONS, 150 KHZ TO 1 GHZ - PART 1: GENERAL CONDITIONS AND DEFINITIONS
    CEN/TR 16152 : 2011 ELECTRONIC FEE COLLECTION - PERSONALISATION AND MOUNTING OF FIRST MOUNT OBE
    EN 55012:2007/A1:2009 VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF OFF-BOARD RECEIVERS
    NF EN 301489-1 : 2012 ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM) - ELECTROMAGNETIC COMPATIBILITY (EMC) STANDARD FOR RADIO EQUIPMENT AND SERVICES - PART 1: COMMON TECHNICAL REQUIREMENTS
    BS EN 60601-1-2:2015 Medical electrical equipment General requirements for basic safety and essential performance. Collateral Standard. Electromagnetic disturbances. Requirements and tests
    10/30237969 DC : DRAFT NOV 2010 BS EN 60810:2003+AMD 2 - LAMPS FOR ROAD VEHICLES - PERFORMANCE REQUIREMENTS
    AAMI IEC 60601-1-2 : 2014 MEDICAL ELECTRICAL EQUIPMENT - PART 1-2: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE - COLLATERAL STANDARD: ELECTROMAGNETIC DISTURBANCES - REQUIREMENTS AND TESTS
    CSA CISPR 16-1-1 : 2015 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-1: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - MEASURING APPARATUS
    EN 61851-21-1:2017/AC:2017-11 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 21-1: ELECTRIC VEHICLE ON-BOARD CHARGER EMC REQUIREMENTS FOR CONDUCTIVE CONNECTION TO AN AC/DC SUPPLY (IEC 61851-21-1:2017)
    BS PD CEN/TR 16152 : 2011 ELECTRONIC FEE COLLECTION - PERSONALISATION AND MOUNTING OF FIRST MOUNT OBE
    15/30271483 DC : 0 BS EN 61851-21-1 ED 1.0 - ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM PART 21-1 ELECTRIC VEHICLE ONBOARD CHARGER EMC REQUIREMENTS FOR CONDUCTIVE CONNECTION TO A.C./D.C. SUPPLY
    NFR 13 007-5 : 1999 ROAD VEHICLES - ELECTROMAGNETIC COMPATIBILITY TEST PROCEDURE OF AUTOMOTIVE COMPONENTS - PART 5: QUALIFICATION OF THE IMMUNITY TO NARROWBAND INTERFERENCE ACCORDING TO THE ABSORPTIVE CHAMBER PROCEDURE
    CISPR 16-1-1:2015 Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus
    CEI EN 61967-1 : 2002 INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC EMISSIONS, 150 KHZ TO 1 GHZ - PART 1: GENERAL CONDITIONS AND DEFINITIONS
    SAE J 2954 : 2017 WIRELESS POWER TRANSFER FOR LIGHT-DUTY PLUG-IN/ELECTRIC VEHICLES AND ALIGNMENT METHODOLOGY
    I.S. EN 60810:2015 LAMPS FOR ROAD VEHICLES - PERFORMANCE REQUIREMENTS
    SAE J 2602/1 : 2012 LIN NETWORK FOR VEHICLE APPLICATIONS
    BS EN 55012 : 2007 VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF OFF-BOARD RECEIVERS
    BS EN 15194:2017 Cycles. Electrically power assisted cycles. EPAC Bicycles
    CEI 79-51 : 2006 COMMUNICATION PROTOCOL FOR SECURITY INFORMATION (ALARMS) - PART 1: TRANSPORT LAYERS
    CSA C108.4 : 2006 VEHICLES, BOATS, AND INTERNAL COMBUSTION ENGINE DRIVEN DEVICES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF RECEIVERS EXCEPT THOSE INSTALLED IN THE VEHICLE/BOAT/DEVICE ITSELF OR IN ADJACENT VEHICLES/BOATS/DEVICES
    I.S. ETSI EN 301489-1 V1.8.1:2009 ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); ELECTROMAGNETIC COMPATIBILITY (EMC) STANDARD FOR RADIO EQUIPMENT AND SERVICES; PART 1: COMMON TECHNICAL REQUIREMENTS
    ISO 11452-3:2016 Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 3: Transverse electromagnetic (TEM) cell
    UNE-EN 13309:2010 Construction machinery - Electromagnetic compatibility of machines with internal power supply
    I.S. EN 13309:2010 CONSTRUCTION MACHINERY - ELECTROMAGNETIC COMPATIBILITY OF MACHINES WITH INTERNAL POWER SUPPLY
    I.S. EN 1846-2:2009 FIREFIGHTING AND RESCUE SERVICE VEHICLES - PART 2: COMMON REQUIREMENTS - SAFETY AND PERFORMANCE
    CEI EN 61000-4-20 : 2013 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-20: TESTING AND MEASUREMENT TECHNIQUES - EMISSION AND IMMUNITY TESTING IN TRANSVERSE ELECTROMAGNETIC (TEM) WAVEGUIDES
    BS EN 61851-21-1:2017 Electric vehicle conductive charging system Electric vehicle on-board charger EMC requirements for conductive connection to an AC/DC supply
    BS EN 55016-1-6 : 2015 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-6: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - EMC ANTENNA CALIBRATION
    BS PD ISO/TS 21609 : 2014 ROAD VEHICLES - (EMC) GUIDELINES FOR INSTALLATION OF AFTERMARKET RADIO FREQUENCY TRANSMITTING EQUIPMENT
    SAE J 2284-5 : 2016 HIGH-SPEED CAN (HSC) FOR VEHICLE APPLICATIONS AT 500 KBPS WITH CAN FD DATA AT 5 MBPS
    15/30321305 DC : 0 BS EN 15194 - CYCLES - ELECTRICALLY POWER ASSISTED CYCLES - EPAC BICYCLES
    SAE J 2497 : 2012 POWER LINE CARRIER COMMUNICATIONS FOR COMMERCIAL VEHICLES
    14/30303404 DC : 0 BS CISPR 12 ED.7.0 - VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENTS FOR THE PROTECTION OFF-BOARD RECIEVES
    I.S. EN 55016-1-1:2010 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-1: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - MEASURING APPARATUS
    06/30157139 DC : 0
    BS EN 61000-4-20:2003 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-20: TESTING AND MEASUREMENT TECHNIQUES - EMISSION AND IMMUNITY TESTING IN TRANSVERSE ELECTROMAGNETIC (TEM) WAVEGUIDES
    SAE J 2578 : 2014 RECOMMENDED PRACTICE FOR GENERAL FUEL CELL VEHICLE SAFETY
    ISO 22902-7:2006 Road vehicles Automotive multimedia interface Part 7: Physical specification
    CISPR 16-1-1:2015 RLV Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus
    BS EN 55016-1-1 : 2010 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-1: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - MEASURING APPARATUS
    BS EN IEC 60810:2018 Lamps, light sources and led packages for road vehicles. Performance requirements
    CSA C22.2 No. 60601.1.2 : 2016 MEDICAL ELECTRICAL EQUIPMENT - PART 1-2: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE - COLLATERAL STANDARD: ELECTROMAGNETIC DISTURBANCES - REQUIREMENTS AND TESTS
    CAN/CSA-Z627-16 Breath alcohol ignition interlock devices
    I.S. EN 60601-1-2:2015 MEDICAL ELECTRICAL EQUIPMENT - PART 1-2: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE - COLLATERAL STANDARD: ELECTROMAGNETIC DISTURBANCES - REQUIREMENTS AND TESTS
    I.S. EN 15194:2017 CYCLES - ELECTRICALLY POWER ASSISTED CYCLES - EPAC BICYCLES
    IEC PAS 62437:2005 Radio disturbance characteristics for the protection of receivers used on board vehicles, boats, and on devices - Limits and methods of measurement - Specifications for active antennas
    IEEE 2030.1.1 : 2015 TECHNICAL SPECIFICATIONS OF A DC QUICK CHARGER FOR USE WITH ELECTRIC VEHICLES
    04/30089279 DC : DRAFT FEB 2004 ISO 21848 - ROAD VEHICLES - ELECTRICAL AND ELECTRONIC EQUIPMENT FOR 42 V NETWORKS - ELECTRICAL LOADS
    UNE-ISO 16750-2:2015 Road vehicles. Environmental conditions and testing for electrical and electronic equipment. Part 2: Electrical loads.
    CISPR 12:2007+AMD1:2009 CSV Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers
    UNI EN 1846-2 : 2013 FIREFIGHTING AND RESCUE SERVICE VEHICLES - PART 2: COMMON REQUIREMENTS - SAFETY AND PERFORMANCE
    UNI EN 13309 : 2010 CONSTRUCTION MACHINERY - ELECTROMAGNETIC COMPATIBILITY OF MACHINES WITH INTERNAL POWER SUPPLY
    I.S. EN IEC 60810:2018 LAMPS, LIGHT SOURCES AND LED PACKAGES FOR ROAD VEHICLES - PERFORMANCE REQUIREMENTS
    SAE J 2284-1 : 2016 HIGH SPEED CAN (HSC) FOR VEHICLE APPLICATIONS AT 125 KBPS
    BS ISO 11452-3 : 2016 ROAD VEHICLES - COMPONENT TEST METHODS FOR ELECTRICAL DISTURBANCES FROM NARROWBAND RADIATED ELECTROMAGNETIC ENERGY - PART 3: TRANSVERSE ELECTROMAGNETIC (TEM) CELL
    ISO 21848:2005 Road vehicles Electrical and electronic equipment for a supply voltage of 42 V Electrical loads
    DD IEC PAS 62437 : 2005 RADIO DISTURBANCE CHARACTERISTICS FOR THE PROTECTION OF RECEIVERS USED ON BOARD VEHICLES, BOATS, AND ON DEVICES - LIMITS AND METHODS OF MEASUREMENT - SPECIFICATIONS FOR ACTIVE ANTENNAS
    SAE J 2357 : 2012 APPLICATION GUIDELINES FOR ELECTRONICALLY DRIVEN AND/OR CONTROLLED EXTERIOR AUTOMOTIVE LIGHTING EQUIPMENT
    13/30292984 DC : 0 BS EN 62153-4-10 ED2 - METALLIC COMMUNICATION CABLE TEST METHODS - PART 4-10: ELECTROMAGNETIC COMPATIBILITY (EMC) - SHIELDED SCREENING ATTENUATION TEST METHOD FOR MEASURING THE SCREENING EFFECTIVENESS OF FEED-THROUGHS AND ELECTROMAGNETIC GASKETS DOUBLE COAXIAL METHOD
    ISO 16750-2:2012 Road vehicles Environmental conditions and testing for electrical and electronic equipment Part 2: Electrical loads
    SAE J 1938 : 2015 PRODUCT DEVELOPMENT PROCESS AND CHECKLIST FOR VEHICLE ELECTRONIC SYSTEMS
    BS IEC 62153-4-10:2015 (published 2015-11) Metallic communication cable test methods Electromagnetic compatibility (EMC). Transfer impedance and screening attenuation of feed-throughs and electromagnetic gaskets. Double coaxial test method
    15/30304065 DC : 0 BS ISO 11452-3 - ROAD VEHICLES - COMPONENT TEST METHODS FOR ELECTRICAL DISTURBANCES FROM NARROWBAND RADIATED ELECTROMAGNETIC ENERGY - PART 3: TRANSVERSE ELECTROMAGNETIC MODE (TEM) CELL
    05/30127980 DC : DRAFT JAN 2005 ISO 13766 - EARTH-MOVING MACHINERY - ELECTROMAGNETIC COMPATIBILITY
    ISO 13766-1:2018 Earth-moving and building construction machinery Electromagnetic compatibility (EMC) of machines with internal electrical power supply Part 1: General EMC requirements under typical electromagnetic environmental conditions
    SAE J 2891 : 2015 AUXILIARY POWER UNIT ELECTRICAL INTERFACE REQUIREMENTS FOR CLASS EIGHT TRUCKS
    I.S. EN 61967-1:2002 INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC EMISSIONS, 150 KHZ TO 1 GHZ - PART 1: GENERAL CONDITIONS AND DEFINITIONS
    EN IEC 60810:2018 LAMPS, LIGHT SOURCES AND LED PACKAGES FOR ROAD VEHICLES - PERFORMANCE REQUIREMENTS (IEC 60810:2017)
    I.S. EN 61851-21-1:2017 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 21-1: ELECTRIC VEHICLE ON-BOARD CHARGER EMC REQUIREMENTS FOR CONDUCTIVE CONNECTION TO AN AC/DC SUPPLY
    IEEE 802.3-2012 ETHERNET - CORRIGENDUM 1: MULTI-LANE TIMESTAMPING
    I.S. EN 55025:2017 VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF ON-BOARD RECEIVERS
    I.S. EN 61000-4-20:2010 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-20: TESTING AND MEASUREMENT TECHNIQUES - EMISSION AND IMMUNITY TESTING IN TRANSVERSE ELECTROMAGNETIC (TEM) WAVEGUIDES
    IEC 61851-21-1:2017 Electric vehicle conductive charging system - Part 21-1 Electric vehicle on-board charger EMC requirements for conductive connection to AC/DC supply
    16/30350012 DC : 0 BS EN 60810 - LAMPS, LIGHT SOURCES AND LED PACKAGES FOR ROAD VEHICLES - PERFORMANCE REQUIREMENTS
    UNE-EN 61000-4-20:2011 Electromagnetic compatibility (EMC) -- Part 4-20: Testing and measurement techniques - Emission and immunity testing in Transverse Electromagnetic (TEM) waveguides - Basic EMC publication
    IEC 60601-1-2:2007 Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral standard: Electromagnetic compatibility - Requirements and tests
    IEC 61000-4-20:2010 Electromagnetic compatibility (EMC) - Part 4-20: Testing and measurement techniques - Emission and immunity testing in transverse electromagnetic (TEM) waveguides
    UNE-EN 1846-2:2011 Firefighting and rescue service vehicles - Part 2: Common requirements - Safety and performance
    IEC 61967-1:2002 Integrated circuits - Measurement of electromagnetic emissions, 150 kHz to 1 GHz - Part 1: General conditions and definitions
    BS EN 60810 : 2015 LAMPS FOR ROAD VEHICLES - PERFORMANCE REQUIREMENTS
    BS EN 1846-2 : 2009 FIREFIGHTING AND RESCUE SERVICE VEHICLES - PART 2: COMMON REQUIREMENTS - SAFETY AND PERFORMANCE
    EN 15194:2017 Cycles - Electrically power assisted cycles - EPAC Bicycles
    EN 1846-2:2009+A1:2013 FIREFIGHTING AND RESCUE SERVICE VEHICLES - PART 2: COMMON REQUIREMENTS - SAFETY AND PERFORMANCE
    CISPR 16-1-1 REDLINE : 4ED 2015 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-1: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - MEASURING APPARATUS
    10/30230478 DC : 0 BS EN 55016-1-6 ED.1 - SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-6: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - EMC-ANTENNA CALIBRATION
    16/30316578 DC : 0 BS EN ISO 13766-1 - EARTH-MOVING- AND BUILDING CONSTRUCTION MACHINERY - ELECTROMAGNETIC COMPATIBILITY OF MACHINES WITH INTERNAL ELECTRICAL POWER SUPPLY - PART 1: GENERAL EMC REQUIREMENTS UNDER TYPICAL EMC ENVIRONMENTAL CONDITIONS
    SAE J 1113/1 : 2013 ELECTROMAGNETIC COMPATIBILITY MEASUREMENT PROCEDURES AND LIMITS FOR COMPONENTS OF VEHICLES, BOATS (UP TO 15 M), AND MACHINES (EXCEPT AIRCRAFT) (16.6 HZ TO 18 GHZ)
    CAN/CSA-CISPR 12-10 (R2018) Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers (Adopted IEC CISPR 12:2007 + A1:2009, edition 6.1, 2009-03, with Canadian deviations) | Véhicules, bateaux et moteurs à combustion interne - Caractéristiques de perturbation radioélectrique - Limites et méthodes de mesure pour la protection des récepteurs extérieurs (norme IEC CISPR 12:2007 + A1:2009 adoptée, édition 6.1, 2009-03, avec exigences propres au Canada)
    16/30269922 DC : 0 BS EN 61851-21-2 ED 1.0 - ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 21-1: EMC REQUIRMENTS FOR OFF BOARD ELECTRIC VEHICLE CHARGING SYSTEMS
    CISPR TR 16-4-4:2007 Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-4: Uncertainties, statistics and limit modelling - Statistics of complaints and a model for the calculation of limits for the protection of radio services
    SAE J 2556 : 2014 RADIATED EMISSIONS (RE) NARROWBAND DATA ANALYSIS - POWER SPECTRAL DENSITY (PSD)
    I.S. EN 55012:2007 VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF OFF-BOARD RECEIVERS
    BS CISPR 12(1997) : 1997 VEHICLES, MOTORBOATS AND SPARK-IGNITED ENGINE-DRIVEN DEVICES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT
    SAE J 1455 : 2017 RECOMMENDED ENVIRONMENTAL PRACTICES FOR ELECTRONIC EQUIPMENT DESIGN IN HEAVY-DUTY VEHICLE APPLICATIONS
    NF EN 55012 : 2008 AMD 1 2009 VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF OFF-BOARD RECEIVERS
    SAE J 2284-3 : 2016 HIGH-SPEED CAN (HSC) FOR VEHICLE APPLICATIONS AT 500 KBPS
    CEI 79-56 : 2009 BLACK BOX TYPE SYSTEMS: FUNCTIONAL REQUIREMENTS AND TESTS
    EN 55025:2017/AC:2017-11 VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF ON-BOARD RECEIVERS (CISPR 25:2016/COR1:2017)
    ISO 13766:2006 Earth-moving machinery Electromagnetic compatibility
    IEC TS 62153-4-1:2014 Metallic communication cable test methods - Part 4-1: Electromagnetic compatibility (EMC) - Introduction to electromagnetic screening measurements
    I.S. EN 55016-1-6:2015 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-6: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - EMC ANTENNA CALIBRATION
    ISO/IEC/IEEE 8802-3:2017 Information technology Telecommunications and information exchange between systems Local and metropolitan area networks Specific requirements Part 3: Standard for Ethernet
    ISO/TS 21609:2014 Road vehicles — (EMC) guidelines for installation of aftermarket radio frequency transmitting equipment
    S.R. CEN/TR 16152:2011 ELECTRONIC FEE COLLECTION - PERSONALISATION AND MOUNTING OF FIRST MOUNT OBE
    DIN EN 13309:2010-12 CONSTRUCTION MACHINERY - ELECTROMAGNETIC COMPATIBILITY OF MACHINES WITH INTERNAL POWER SUPPLY
    BS ISO 21848 : 2005 ROAD VEHICLES - ELECTRICAL AND ELECTRONIC EQUIPMENT FOR A SUPPLY VOLTAGE OF 42 V - ELECTRICAL LOADS
    BS EN 13309:2010 (published 2010-08) Construction machinery. Electromagnetic compatibility of machines with internal power supply
    DIN EN 1846-2:2013-05 Firefighting and rescue service vehicles - Part 2: Common requirements - Safety and performance (includes Amendment A1:2013)
    EN 55016-1-6:2015/A1:2017 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-6: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - EMC ANTENNA CALIBRATION (CISPR 16-1-6:2014/A1:2017)
    EN 55016-1-1:2010/A2:2014 SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS AND METHODS - PART 1-1: RADIO DISTURBANCE AND IMMUNITY MEASURING APPARATUS - MEASURING APPARATUS (CISPR 16-1-1:2010/A2:2014)

    Standards Referencing This Book - (Show below) - (Hide below)

    CISPR 12:2007+AMD1:2009 CSV Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers
    ISO 7637-3:2016 Road vehicles — Electrical disturbances from conduction and coupling — Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines
    CISPR 16-1-4:2010+AMD1:2012+AMD2:2017 CSV Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements
    CISPR 16-1-1:2015 Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus
    ISO 11452-4:2011 Road vehicles Component test methods for electrical disturbances from narrowband radiated electromagnetic energy Part 4: Harness excitation methods
    CISPR 16-2-1:2014 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-1: Methods of measurement of disturbances and immunity - Conducted disturbance measurements
    SAE ARP 958 : 1999 ELECTROMAGNETIC INTERFERENCE MEASUREMENT ANTENNAS; STANDARD CALIBRATION METHOD
    CISPR 22:2008 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement
    CISPR 16-2-3:2016 Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of measurement of disturbances and immunity - Radiated disturbance measurements
    IEEE 1128 : 1998 RECOMMENDED PRACTICE FOR RADIO-FREQUENCY (RF) ABSORBER EVALUATION IN THE RANGE OF 30 MHZ TO 5 GHZ
    AS CISPR 16.1.1:2020 Specification for radio disturbance and immunity measuring apparatus and methods Radio disturbance and immunity measuring apparatus - Measuring apparatus (CISPR 16-1-1:2019 (ED 5.0) MOD)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective