DD CEN/TS 1555-7:2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) Guidance for the assessment of conformity
Hardcopy , PDF
31-03-2013
English
08-01-2004
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
3.1 Terms and definitions
3.2 Abbreviations
4 Requirements
4.1 General
4.2 Testing and inspection
4.3 Technical file
Annex A (normative) Change of compound
A.1 General
A.2 Change
A.3 Type testing required for re-evaluation
Bibliography
Provides guidance for assessment of conformity to be included in the manufacturer's quality plan as part of the quality system.
| Committee |
PRI/88
|
| DevelopmentNote |
Supersedes 95/125454 DC (03/2004)
|
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
British Standards Institution
|
| RevisionOf | |
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| CEN/TS 1555-7:2003 | Identical |
| BS 5391-1:2006 | Acrylonitrile-butadiene-styrene (ABS) pressure pipe Specification |
| EN ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009) |
| EN 1555-1:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General |
| EN 1555-3:2010+A1:2012 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| ISO 13953:2001 | Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| EN 728:1997 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| ISO 10838-3:2001 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| EN 45011:1998 | General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) |
| ISO 10838-2:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm |
| ISO 10838-1:2000 | Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm |
| ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| EN 45011 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
| ISO 6259-1:2015 | Thermoplastics pipes Determination of tensile properties Part 1: General test method |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 13954:1997 | Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| EN 1555-4:2011 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves |
| ISO 13955:1997 | Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies |
| EN 1555-5:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 12007-2:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| EN 1555-2:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| ISO 6259-3:2015 | Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes |
| EN 45012 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
| EN ISO 9000:2015 | Quality management systems - Fundamentals and vocabulary (ISO 9000:2015) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.