DEFSTAN 00-970(PT1)SEC6/14(2015) : 2015
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 1: FIXED WING - SECTION 6: EQUIPMENT
Available format(s)
Hardcopy , PDF
Superseded date
13-07-2015
Superseded by
Language(s)
English
Published date
01-01-2015
Publisher
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Preface
SECTION 6 - EQUIPMENT
6.0 Introduction
6.1 General
6.2 Avionic Equipment Installations
6.3 Static Pressure Systems
6.4 Magnetic Compass Installations
6.5 Automatic Pilot Systems
6.6 Electrical Systems
6.7 Lights
6.8 Safety Equipment
6.9 Ice Protection
6.10 EMC of Safety Critical Systems
6.11 Hydraulic Systems
6.12 Pneumatic Systems
6.13 Oxygen Systems
6.14 Pressurised Gas Storage Vessels
6.15 Data Recording Systems
SUPPLEMENTS
Leaflets 0 to 35
Describes the requirements relating to equipment and systems embodied on any aircraft.
| DevelopmentNote |
Supersedes DEFSTAN 00-970(PT1)SEC6/13(2014). (04/2015)
|
| DocumentType |
Standard
|
| Pages |
251
|
| PublisherName |
UK Ministry of Defence Standards
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| BS C 18:1976 | Specification for V-flange couplings for aircraft piping and ducting - metric series |
| DEFSTAN 00-35(PT4)/4(2006) : 2006 | ENVIRONMENTAL HANDBOOK FOR DEFENCE MATERIEL - PART 4: NATURAL ENVIRONMENTS |
| BS G 230:1984 | Specification for general requirements for aircraft electrical cables (second series) |
| BS 2G 143:1965 | Specification for a.c. and d.c. rotary and linear actuators for aircraft |
| BS J12(1966) : LATEST | |
| BS 2G 180:1974 | Specification for permanent splicing of aircraft electrical cables |
| DEFSTAN 00-13/3(1994) : 1994 | REQUIREMENTS FOR THE ACHIEVEMENT OF TESTABILITY IN ELECTRONIC AND ALLIED EQUIPMENT |
| BS 2G 134:1970 | Specification for d.c. generators |
| BS 2G 210:1991 | Specification for PTFE insulated equipment wires and cables, single and multi-core, with silver plated copper conductors (190°C) or nickel plated copper conductors (260°C) |
| BS M 43:1973 | Methods of zoning aircraft and referencing access doors and panels |
| DEFSTAN 81-24/5(2004) : 2004 | IDENTIFICATION MARKING OF TRANSPORTABLE CONTAINERS, COMPRESSED GAS |
| BS M 55:1984 | Method for rotary flexure testing of hydraulic tubing joints and fittings for aerospace use |
| DEFSTAN 00-35(PT5)/4(2006) : 2006 | ENVIRONMENTAL HANDBOOK FOR DEFENCE MATERIEL - PART 5: INDUCED MECHANICAL ENVIRONMENTS |
| BS 5M 23:1987 | Specification for an identification scheme for pipelines |
| BS M 51:1982 | Classification for pressure and temperature for fluid systems and components |
| DEFSTAN 59-97/3(1990) : AMD 1 | HEAT SHRINKABLE INSULATION MATERIALS - GENERAL REQUIREMENTS, TESTS AND TEST METHODS FOR CAPABILITY APPROVAL |
| DEFSTAN 05-42/2(1982) : 1982 | PARTICULATE CONTAMINATION CLASSES FOR FLUIDS IN HYDRAULIC SYSTEMS |
| MIL-STD-810 Revision G:2008 | ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS |
| BS G 231:1983 | Specification for conductors for general purpose aircraft electrical cables and aerospace applications |
| BS G 207:1969 | Specification for aircraft electrical circuit diagrams |
| BS 3G 197:1982 | Specification for stud-type terminal blocks for terminations on aircraft electric cables |
| MIL A 5498 : D | ACCUMULATORS, HYDRAULIC, CYLINDRICAL 3000 PSI, AIRCRAFT |
| DEFSTAN 01-5/17(2011) : 2011 | FUELS, LUBRICANTS AND ASSOCIATED PRODUCTS |
| ISO 6771:2007 | Aerospace — Fluid systems and components — Pressure and temperature classifications |
| DEFSTAN 00-35(PT1)/4(2006) : 2006 | ENVIRONMENTAL HANDBOOK FOR DEFENCE MATERIEL - PART 1: CONTROL AND MANAGEMENT |
| DEFSTAN 05-43/1(1977) : 1977 | STANDARD PROCEDURES FOR TAKING SAMPLES OF HYDRAULIC FLUIDS FOR EVALUATION OF PARTICULATE CONTAMINATION |
| DEFSTAN 61-12(PT9)/5(2008) : 2008 | WIRES, CORDS AND CABLES ELECTRICAL - METRIC UNITS - PART 9: CABLES AND WIRES ELECTRICAL FOR CABLES, RADIO FREQUENCY INCLUDING LIMITED FIRE HAZARD (LFH) VARIANTS |
| MIL-STD-1760 Revision E:2007 | AIRCRAFT/STORE ELECTRICAL INTERCONNECTION SYSTEM |
| BS M 52:1983 | Method for impulse testing of hydraulic hose, tubing and fittings assemblies for aerospace fluid systems |
| BS 2G 202:1988 | Specification for design and performance requirements for airframe-fit electrical connectors for d.c. and low frequency a.c. applications |
| DEFSTAN 59-35(PT0)/3(1990) : 1990 | CONNECTORS ELECTRICAL - PART 0: GUIDE TO CONNECTORS ELECTRICAL, DIRECT CURRENT, LOW FREQUENCY AND RADIO FREQUENCY APPLICATIONS |
| BS G 212:1971 | Specification for general requirements for aircraft electrical cables |
| MIL E 5400 : T | ELECTRONIC EQUIPMENT, AEROSPACE, GENERAL SPECIFICATION FOR |
| BS 2G 127:1967 | Specification for power and current transformers for use in aircraft electrical power supply systems |
| BS 2G 100-2:1962 | Specification for general requirements for electrical equipment and indicating instruments for aircraft Environmental and operating conditions |
| ISO 6772:2012 | Aerospace — Fluid systems — Impulse testing of hydraulic hose, tubing and fitting assemblies |
| BS M 53:1983 | Method for thermal shock testing of pipes and fittings for aerospace fluid systems |
| STANAG 3323 : 0 | PIPE (TUBE) CONNECTIONS TO AIRCRAFT INSTRUMENTS (IMPERIAL AND METRIC) |
| BS G 232:1984 | Specification for electric cables for general airframe or equipment interconnect use (135°C), wrapped insulation |
| DEFSTAN 00-31/1(1987) : 1987 | THE DEVELOPMENT OF SAFETY CRITICAL SOFTWARE FOR AIRBORNE SYSTEMS |
| BS M 44:1974 | Specification for identification of aircraft servicing, maintenance, ground handling and safety/hazard points |
| ISO 7169:2014 | Aerospace Separable tube fittings for fluid systems, for 24 degree cones, for pressures up to 3 000 psi or 21 000 kPa Procurement specification, inch/metric |
| DEFSTAN 00-971/1(1987) : 1987 | GENERAL SPECIFICATION FOR AIRCRAFT GAS TURBINE ENGINES |
| DOD STD 1788 : LATEST | AVIONICS INTERFACE DESIGN STANDARD (METRIC) |
| BS G 209:1970 | Specification for transformer rectifier units |
| DEFSTAN 00-35(PT3)/4(2006) : 2006 | ENVIRONMENTAL HANDBOOK FOR DEFENCE MATERIEL - PART 3: ENVIRONMENTAL TEST METHODS |
| MIL-PRF-5503 Revision G:2013 | ACTUATORS: AERONAUTICAL LINEAR UTILITY, HYDRAULIC, GENERAL SPECIFICATION FOR |
| BS M 48:1975 | Specification for dimensions of elastomeric toroidal sealing rings for aerospace use - inch series |
| BS 5G 205-1:1990 | Secondary batteries for aircraft Specification for lead-acid batteries |
| BS M 60:1986 | Specification for separable tube fittings for fluid systems |
| BS 2G 146:1966 | Specification for d.c. motors for aircraft |
| BS G 203:1967 | Specification for Unified screws with captive facing and locking washers |
| BS 2G 223:1989 | Specification for screen terminating devices for aircraft electric cables |
| BS 2G 229:1987 | Schedule for environmental conditions and test procedures for airborne equipment |
| MIL-STD-461 Revision G:2015 | REQUIREMENTS FOR THE CONTROL OF ELECTROMAGNETIC INTERFERENCE CHARACTERISTICS OF SUBSYSTEMS AND EQUIPMENT |
| BS 2G 199:1984 | Schedule for tables relating to altitudes, airspeed and Mach numbers for use in aeronautical instrument design and calibration |
| BS 6275-1:1982 | Hydraulic fluid power filter elements Method of evaluating filtration performance (multi-pass method) |
| BS C 13:1960 | Sizes of gravity filling orifices on aircraft |
| DEFSTAN 61-10/4(1984) : 1984 | GENERATOR SETS (GROUND, ENGINE DRIVEN) |
| MIL-D-81641 Base Document:1972 | Display, Head-up, General Specification for |
| DEFSTAN 00-41(PT1)/2(1989) : 1989 | MOD PRACTICES AND PROCEDURES FOR RELIABILITY AND MAINTAINABILITY - PART 1: RELIABILITY DESIGN PHILOSOPHY |
| MIL-H-8775 Revision D:1976 | HYDRAULIC SYSTEM COMPONENTS, AIRCRAFT AND MISSILES GENERAL SPECIFICATION FOR |
| BS G 233:1984 | Specification for electric cables for general airframe or equipment interconnect use (135°C), extruded insulation |
| BS 2G 196:1971 | Specification for static invertors |
| MIL D 87213 : 0 | DISPLAYS/OPTICALLY GENERATED REQUEST FOR ISSUE OTHER THAN DOD MUST BE SENT VIA; ASD/ENES, WRIGHT-PATTERSON AFB OH 45433-6503 |
| ISO 7257:2016 | Aircraft Hydraulic tubing joints and fittings Rotary flexure test |
| BS 2G 219:1983 | Specification for general requirements for ground support electrical supplies for aircraft |
| BS C 9:1970 | Specification for coupling dimensions for high pressure air charging valves for aircraft |
| MIL F 8815 : D | FILTER AND FILTER ELEMENTS, FLUID PRESSURE, HYDRAULIC LINE, 15 MICRON ABSOLUTE AND 5 MICRON ABSOLUTE, TYPE 11 SYSTEMS; GENERAL SPECIFICATION FOR |
| MIL-H-5440 Revision H:1993 | HYDRAULIC SYSTEMS, AIRCRAFT, TYPES 1 AND 11 DESIGN AND INSTALLATION REQUIREMENTS FOR |
| BS 2G 100-3:1968 | General requirements for aircraft electrical equipment and indicating in struments Characteristics of aircraft electrical systems |
| BS G 217:1975 | Specification for general requirements for cockpit lighting controllers |
| ARINC 404A : 1974 | AIR TRANSPORT EQUIPMENT CASES AND RACKING |
| BS G 194:1965 | Specification for lever-operated manual switches for aircraft |
| BS G 102:1971 | Specification for general requirements for rotating electrical machinery |
| MIL-W-5088 Revision L:1991 | Wiring, Aerospace Vehicle (Future Design Should Refer to SAE-AS50881) |
| BS 4G 229:1996 | Schedule for environmental conditions and test procedures for airborne equipment |
| MIL-I-8700 Revision A:1970 | INSTALLATION AND TEST OF ELECTRONIC EQUIPMENT IN AIRCRAFT, GENERAL SPECIFICATION FOR |
| BS G 222:1976 | Specification for Efglas type electric cables (metric units) |
| DEFSTAN 00-970/VOL1/1(1983) : AMD 14 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - AEROPLANES |
| DEFSTAN 00-970/VOL2/1(1984) : 1984 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - ROTORCRAFT |
| STANAG 3212 : 2017 | DIAMETERS FOR GRAVITY FILLING ORIFICES |
| DEFSTAN 00-52/4(2014) : 2014 | THE GENERAL REQUIREMENTS FOR PRODUCT ACCEPTANCE AND MAINTENANCE TEST SPECIFICATIONS AND TEST SCHEDULES |
| ISO 6773:1994 | Aerospace Fluid systems Thermal shock testing of piping and fittings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.