DEFSTAN 02-179/1(2002) : 2002
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
REQUIREMENTS FOR LOCKERS (MAGAZINE, RU MAGAZINE AND DETONATOR) USED FOR STORAGE OF EXPLOSIVE STORES IN HM SURFACE SHIPS AND SUBMARINES
23-08-2019
12-01-2013
SCOPE
FOREWORD
Sponsorship
Conditions of Release
Categories of Naval Defence Standard
Related Documents
Health and Safety
Additional Information
CONTENTS
SECTION 1 - PERFORMANCE SPECIFICATION
1.1 General
1.2 Environmental Conditions
SECTION 2 - NATIONAL/INTERNATIONAL REGULATIONS
SECTION 3 - MILITARY STANDARDS/REQUIREMENTS
3.1 General Requirements
3.1.1 Distortion/Racking (due to flooding)
3.1.2 Base/Legs
3.1.3 Shock (Non-Contact Underwater Explosion)
3.1.4 Electrical Screening
3.1.5 Response to Attack on Ammunition
3.1.6 Insulation/Cladding Plates
3.1.7 Radar Cross Section (Radar Echo Area)
3.1.8 Radar Absorbent Material
3.1.9 Welding
3.1.10 Galvanizing
3.1.11 Painting
3.1.11.1 Surface Coatings for Detonator
Lockers only
3.1.11.2 External Coatings
3.1.11.3 Internal Coatings
3.1.12 Locker Doors and Lids
3.1.12.1 Door Seals
3.1.12.2 Hinges
3.1.12.3 Locking Arrangements
3.1.12.4 Clips and Closing Arrangements
3.1.13 Flooding Connection
3.1.14 Drainage Arrangements
3.1.15 Venting
3.1.16 Configuration
3.1.17 Interchangeability
3.1.18 Stowage Arrangements
3.1.19 Identification
3.1.20 Representative Inert Rounds/Ammunition
Boxes
3.1.21 Fittings
3.1.22 Maximum/Minimum Thermometer Bracket
3.1.23 Temperature Card Holder
3.1.24 Magazine Designed Capacity List - S285K
3.1.25 Notice board
3.1.26 Tally/Marker Plates
3.1.27 Warning Notices
3.1.28 Detonator Lockers
3.1.28.1 Deck Mounted
3.1.28.2 Bulkhead Mounted
3.2 Test and Trials
SECTION 4 - DESIGN REQUIREMENTS/GUIDANCE
4.1 Construction
4.2 Material
4.3 Composite Material
4.3.1 General Construction
4.3.2 Locker Carcass
4.3.3 Locker Coatings
SECTION 5 - CORPORATE EXPERIENCE & KNOWLEDGE
ANNEX A - RELATED DOCUMENTS
ANNEX B - ABBREVIATIONS AND DEFINITIONS
ANNEX C - PROCUREMENT CHECK LIST
ANNEX D - CHECK LIST FOR A NEW/REFURBISHED MAGAZINE LOCKER OR
READY-USE MAGAZINE LOCKER
ANNEX E - CURRENT RANGE OF AMMUNITION AND DETONATOR LOCKERS
ALPHABETICAL INDEX
Describes the specific requirements for the design, production and fitting out of Magazine, Detonator and Ready-use Magazine Lockers.
| DevelopmentNote |
Supersedes DEFSTAN 08-146/1(2001). (06/2002) This standard is obsolescent because it is no longer required for the procurement of new equipment but is retained for maintenance purposes in support of existing in-service equipment. (04/2012)
|
| DocumentType |
Standard
|
| PublisherName |
UK Ministry of Defence Standards
|
| Status |
Withdrawn
|
| Supersedes |
| DEFSTAN 00-101(PT1)/2(2008) : 2008 | DESIGN STANDARDS FOR EXPLOSIVES SAFETY IN MOD SHIPS AND SUBMARINES - PART 1: SURFACE SHIPS |
| BS 381C:1996 | Specification for colours for identification, coding and special purposes |
| DEFSTAN 80-125/2(1999) : 1999 | PAINT, FINISHING, EMULSION, FOR CANVAS, BRUSHING |
| BS EN 12167:2011 | Copper and copper alloys. Profiles and bars for general purposes |
| DEFSTAN 08-123/1(2000) : 2000 | REQUIREMENTS FOR THE DESIGN AND TESTING OF EQUIPMENTS TO MEET ENVIRONMENTAL CONDITIONS - CATEGORY 2 |
| DEFSTAN 02-758/1(2000) : 2000 | REQUIREMENTS FOR WEATHERWORK PREPARATION AND PAINTING OF SURFACE SHIPS |
| DEFSTAN 80-165/1(1993) : INTERIM | PAINT SYSTEM FOR SHIP'S WEATHERWORK, HIGH DURABILITY, LIGHT WEATHERWORK GREY - TYPE: BRUSHING |
| DEFSTAN 02-723/1(2000) : 2000 | REQUIREMENTS FOR MARKER PLATES |
| DEFSTAN 80-78/2(1995) : 1995 | PAINT, FINISHING, FLAME RETARDANT, BRUSHING |
| DEFSTAN 02-706/1(2000) : 2000 | WELDING AND FABRICATION OF SHIP'S STRUCTURE |
| DEFSTAN 08-101(PT2)/1(2000) : 2000 | REQUIREMENTS FOR THE CONSTRUCTION AND SYSTEM ARRANGEMENTS IN MAGAZINES AND WEAPON STORAGE COMPARTMENTS - CATEGORY 1 - PART 2: HM SUBMARINES |
| BS EN ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test methods |
| DEFSTAN 02-759/1(2000) : 2000 | USE OF PRE-TREATMENT PRIMER CATEGORY 3 |
| DEFSTAN 02-167/1(2000) : 2000 | REQUIREMENTS FOR RESIN POLYESTER FOR SHIP STRUCTURES |
| DEFSTAN 80-187/1(1993) : INTERIM | PAINT SYSTEM FOR SHIPS' WEATHERWORK - PAINT PRIMING, SHIPS' - WEATHERWORK - PAINT UNDERCOAT, SHIPS' WEATHERWORK - PAINT FINISHING, SHIPS' WEATHERWORK - TYPE: BRUSHING |
| DEFSTAN 08-101(PT1)/1(2000) : 2000 | REQUIREMENTS FOR THE CONSTRUCTION AND SYSTEM ARRANGEMENTS IN MAGAZINES AND WEAPON STORAGE COMPARTMENTS - CATEGORY 1 - PART 1: HM SURFACE SHIPS |
| DEFSTAN 02-154/1(2000) : 2000 | DESIGN STANDARDS FOR SURFACE SHIP STRUCTURES |
| BS EN 12163:2011 | Copper and copper alloys. Rod for general purposes |
| BS EN 12164:2011 | Copper and copper alloys. Rod for free machining purposes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.