DIN 16772-2:1988-12

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTIC MOULDING MATERIALS - ACRYLONITRILE BUTADIENE STYRENE (ABS) MOULDING MATERIALS - PREPARATION OF SPECIMENS AND DETERMINATION OF THEIR PROPERTIES

Available format(s):

Superseded date: 01-10-1999

Language(s):

Published date: 12-01-2013

Publisher: German Institute for Standardisation (Deutsches Institut für Normung)

Table of Contents - (Show below) - (Hide below)

Kein Inhaltsverzeichnis in der Norm vorhanden.

Abstract - (Show below) - (Hide below)

Outlines methods of preparing specimens and determining characteristic properties of ABS moulding materials, as defined in DIN 16772 Pt 1, and other properties, with the aim ofa chieving reproducible results when these properties are measured. Properties of products made of these materials are influenced by type of moulding material used, component design and final condition of the products, these in turn being dependent upon manufacturing conditions and type of subsequent treatment applied. Therefore, values obtained from using test methods set out, are only applicable to specimens of the form specified, prepared as specified, and not to specimens of different dimensions or prepared by different procedures.

General Product Information - (Show below) - (Hide below)

Document Type	Standard
ISBN
Pages
Published
Publisher	German Institute for Standardisation (Deutsches Institut für Normung)
Status	Superseded

Standards Referenced By This Book - (Show below) - (Hide below)

DIN 7741-1:1986-12	PLASTIC MOULDING MATERIALS; POLYSTYRENE (PS) MOULDING MATERIALS; CLASSIFICATION AND DESIGNATION
DIN 16772-1:1987-09	PLASTIC MOULDING MATERIALS - ACRYLONITRILE BUTADIENE STYRENE (ABS) MATERIALS - CLASSIFICATION AND DESIGNATION

Standards Referencing This Book - (Show below) - (Hide below)

DIN 53460:1976-12	TESTING OF PLASTICS; DETERMINATION OF THE VICAT SOFTENING TEMPERATURE OF THERMOPLASTICS
DIN 53448:1977-05	TESTING OF PLASTICS; TENSILE IMPACT TEST
DIN 53735:1988-02	TESTING OF PLASTICS; DETERMINATION OF THE MELT FLOW INDEX OF THERMOPLASTICS
DIN 16770-1:1989-02	TESTING OF PLASTICS - PREPARATION OF SPECIMENS OF THERMOPLASTIC MOULDING MATERIALS BY COMPRESSION MOULDING
DIN 16772-1:1987-09	PLASTIC MOULDING MATERIALS - ACRYLONITRILE BUTADIENE STYRENE (ABS) MATERIALS - CLASSIFICATION AND DESIGNATION
DIN 53752:1980-12	TESTING OF PLASTICS; DETERMINATION OF THE COEFFICIENT OF LINEAR THERMAL EXPANSION
DIN 53728-4:1975-03	TESTING OF PLASTICS - DETERMINATION OF VISCOSITY OF SOLUTIONS, POLYETHYLEN (PE) AND POLYPROPYLENE (PP) IN DILUTE SOLUTION
DIN 53456:1973-01	TESTING OF PLASTICS; INDENTATION HARDNESS TEST
DIN 54811:1984-05	TESTING OF PLASTICS; DETERMINING THE FLUIDITY OF PLASTICS MELTS BY THE CAPILLARY RHEOMETER
ISO 180:2000	Plastics Determination of Izod impact strength
DIN 53461:1987-01	TESTING OF PLASTICS; DETERMINATION OF HEAT DEFLECTION TEMPERATURE UNDER LOAD
DIN 16770-2:1986-05	TESTING OF PLASTICS - TEST SPECIMENS OF THERMOPLASTIC MATERIALS - INJECTION MOULDING
DIN 50014:1985-07	CLIMATES AND THEIR TECHNICAL APPLICATION; STANDARD ATMOSPHERES

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart