• There are no items in your cart

DIN 2609:1991-02

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

STEEL BUTT-WELDING PIPE FITTINGS - TECHNICAL DELIVERY CONDITIONS

Available format(s)

Hardcopy , PDF

Superseded date

01-06-2008

Language(s)

English

Published date

12-01-2013

1 Anwendungsbereich
2 Bestellung
3 Werkstoffe
4 Anforderungen
  4.1 Herstellungsverfahren
  4.2 Lieferzustand
  4.3 Chemische Zusammensetzung
  4.4 Mechanische Eigenschaften
  4.5 Schweisseignung
  4.6 Oberflächenbeschaffenheit
  4.7 Masse und Masstoleranzen
5 Prüfungen und Bescheinigungen
 über Materialprüfungen
  5.1 Allgemeines
  5.2 Ort der Prüfung
  5.3 Prüfumfang
  5.4 Probenentnahme und Probenvorbereitung
  5.5 Durchführung der Prüfungen
  5.6 Wiederholungsprüfungen
  5.7 Bescheinigungen über Materialprüfungen
6 Kennzeichnung
7 Beanstandungen

Specifies technical delivery conditions for unalloyed and alloyed steel butt-welding pipe fittings in compliance with DIN 2605 Part 1 or 2, DIN 2615 Part 1 or 2 (at present at the stage of draft), DIN 2616 Part 1 or 2, or DIN 2617. Where such fittings fall under the scope of the regulations pertaining to plants subject to mandatory inspection as referred to in Section 24 of the Gewerbeordnung (German Trade Regulation).

DocumentType
Standard
Pages
12
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded
SupersededBy

DIN 2605-1:1991-02 STEEL BUTT-WELDING PIPE FITTINGS - ELBOWS AND BENDS WITH REDUCED PRESSURE FACTOR
DIN 2617:1991-02 STEEL BUTT-WELDING PIPE FITTINGS - CAPS
DIN 11852:2009-05 Fittings for the food and chemical industries - Fittings of stainless steel - Tees, bends and reducers for welding
DIN 2615-2:1992-05 STEEL BUTT-WELDING PIPE FITTINGS - TEES FOR USE AT FULL SERVICE PRESSURE
DIN 2430-1:2009-02 PIPING FOR PIGGING SYSTEMS - PART 1: PIPES AND ELBOWS
DIN 2615-1:1992-05 STEEL BUTT-WELDING PIPES FITTINGS - TEES WITH REDUCED PRESSURE FACTOR

DIN 2615-2:1992-05 STEEL BUTT-WELDING PIPE FITTINGS - TEES FOR USE AT FULL SERVICE PRESSURE
DIN 8563-3:1985-10 QUALITY ASSURANCE OF WELDING OPERATIONS; FUSION WELDED JOINTS IN STEEL (EXCEPT BEAM WELDED JOINTS); REQUIREMENTS, CLASSIFICATION
DIN 17100:1980-01 STEELS FOR GENERAL STRUCTURAL PURPOSES - QUALITY STANDARD
DIN 50120-2:1978-08 TESTING OF STEEL; TENSILE TEST ON WELDED JOINTS; PRESSURE WELDED BUTT JOINTS
DIN 8563-1:1978-10 QUALITY ASSURANCE OF WELDED STRUCTURES; FUNDAMENTALS
DIN 17102:1983-10 WELDABLE NORMALIZED FINE GRAIN STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS FOR PLATE, STRIP, WIDE FLATS, SECTIONS AND BARS
DIN 50049:1992-04 METALLIC PRODUCTS; TYPES OF INSPECTION DOCUMENTS
DIN 17457:1985-07 WELDED CIRCULAR AUSTENITIC STAINLESS STEEL TUBES SUBJECT TO SPECIAL REQUIREMENTS - TECHNICAL DELIVERY CONDITIONS
DIN 1626:1984-10 WELDED CIRCULAR UNALLOYED STEEL TUBES SUBJECT TO SPECIAL REQUIREMENTS - TECHNICAL DELIVERY CONDITIONS
DIN 17010:1985-06 GENERAL TECHNICAL DELIVERY CONDITIONS FOR STEEL AND STEEL PRODUCTS
DIN 17458:1985-07 SEAMLESS CIRCULAR AUSTENITIC STAINLESS STEEL TUBES SUBJECT TO SPECIAL REQUIREMENTS - TECHNICAL DELIVERY CONDITIONS
DIN 50145:1975-05 TESTING OF METALLIC MATERIALS; TENSILE TEST
DIN 2615-1:1992-05 STEEL BUTT-WELDING PIPES FITTINGS - TEES WITH REDUCED PRESSURE FACTOR
DIN 17280:1985-07 STEELS WITH LOW TEMPERATURE TOUGHNESS - TECHNICAL DELIVERY CONDITIONS FOR PLATE, SHEET, STRIP, WIDE FLATS, SECTIONS, BARS AND FORGINGS
DIN 2605-1:1991-02 STEEL BUTT-WELDING PIPE FITTINGS - ELBOWS AND BENDS WITH REDUCED PRESSURE FACTOR
DIN 50150:2000-10 TESTING OF METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES
DIN 2617:1991-02 STEEL BUTT-WELDING PIPE FITTINGS - CAPS
DIN 50914:1996-09 TESTING THE RESISTANCE OF STAINLESS STEELS TO INTERGRANULAR CORROSION - METHOD BY USING COPPER SULFATE AND SULFURIC ACID - STRAUSS TEST
DIN 50120-1:1975-09 TESTING OF STEEL - TENSILE TEST ON FUSION WELDED BUTT JOINTS
DIN 1629:1984-10 SEAMLESS CIRCULAR UNALLOYED STEEL TUBES SUBJECT TO SPECIAL REQUIREMENTS - TECHNICAL DELIVERY CONDITIONS
DIN 17155:1983-10 CREEP RESISTANT STEEL PLATE AND STRIP - TECHNICAL DELIVERY CONDITIONS
DIN 8563-2:1978-10 QUALITY ASSURANCE OF WELDED STRUCTURES - REQUIREMENTS ON FIRM
DIN 50351:1985-02 TESTING OF METALLIC MATERIALS - BRINELL HARDNESS TEST
DIN 17440:2001-03 STAINLESS STEELS - TECHNICAL DELIVERY CONDITIONS FOR DRAWN WIRE

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.