• Shopping Cart
    There are no items in your cart

DIN 50100:2015-11 (Draft)

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

LOAD CONTROLLED FATIGUE TESTING - EXECUTION AND EVALUATION OF CYCLIC TESTS AT CONSTANT LOAD AMPLITUDES ON METALLIC SPECIMENS AND COMPONENTS

Available format(s)

Hardcopy , PDF

Superseded date

07-03-2021

Language(s)

German

Published date

01-01-2015

€184.58
Excluding VAT

1 Purpose of test
2 Definitions, symbols and ranges of continuous vibration
      loading
      2.1 Definitions and symbols
      2.2 Ranges of loading
3 Definitions and symbols of continuous vibration strength
      3.1 Definitions of continuous vibration strength
             3.1.1 Continuous vibration strength
             3.1.2 Fatigue strength under completely
                      reversed stress
             3.1.3 Pulsating fatigue strength
      3.2 Symbols of continuous vibration strength and
             their meaning
      3.3 Continuous vibration strength notation
             3.3.1 General
             3.3.2 Identification symbols for continuous
                      vibration loading
             3.3.3 Identification symbols for special
                      influences
4 Special definitions
      4.1 Fatigue strength of large structures
      4.2 Ultimate number of cycles
      4.3 Fatigue strength for finite life
      4.4 Life span
      4.5 Continuous yield limit
      4.6 Continuous creep limit
5 Test procedure
      5.1 General directions
      5.2 Wohler test
      5.3 Multiple-stage test
             5.3.1 Continuous vibration tests in on load
                      stage
             5.3.2 Multiple-stage continuous vibration
                      tests
             5.3.3 Vibration tests under actual service
                      conditions
      5.4 Testing in series
      5.5 Single tests
             5.5.1 Single tests for comparison
             5.5.2 Control tests
      5.6 Testing of weakest points in a structural member
6 Evaluation of test
      6.1 S-N diagram, Wohler curve
      6.2 Fatigue strength diagram
             6.2.1 Definition
             6.2.2 Smith's fatigue strength diagram
             6.2.3 Haigh's diagram
             6.2.4 Other fatigue strength diagrams
                      6.2.4.1 Gerber's, Launhard-
                                 Weyrauch's, Goodman,
                                 Kommerell and Ros fatigue
                                 strength diagram
                      6.2.4.2 Pohl's diagram
                      6.2.4.3 Combination of Smith's and
                                 Pohl's diagrams
                      6.2.4.4 Moore-Kommers- Jasper's
                                 diagram
7 Special test methods
      7.1 Continuous vibration tests at high and low
             temperatures
      7.2 Continuous vibration test under corrosion
      7.3 Continuous vibration tests under fretting
             corrosion
      7.4 Continuous vibration tests with composite
             loading
      7.5 Notch sensitivity
      7.6 Fatigue notch factor
8 Additional definitions used in the continuous
      vibration test
      8.1 Fracture, crack
      8.2 Continuous vibration fracture, static fracture,
             continuous vibration crack, final fracture,
             arrest lines
      8.3 Coaxing
      8.4 Damping capacity of materials
      8.5 Expanded Wohler diagram (damage line)

DocumentType
Draft
Pages
110
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded

BS EN 60601-2-36:2015 Medical electrical equipment Particular requirements for the basic safety and essential performance of equipment for extracorporeally induced lithotripsy
BS 5724-2.36(1997) : 1997 MEDICAL ELECTRICAL EQUIPMENT - PARTICULAR REQUIREMENTS FOR SAFETY - SPECIFICATION FOR EQUIPMENT FOR EXTRA-CORPOREALLY INDUCED LITHOTRIPSY
DIN 685-3:2001-02 ROUND STEEL LINK CHAINS, TESTED - PART 3: TEST
I.S. EN 60601-2-36:2015 MEDICAL ELECTRICAL EQUIPMENT - PART 2-36: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF EQUIPMENT FOR EXTRACORPOREALLY INDUCED LITHOTRIPSY
DIN 50282:1979-02 PLAIN BEARINGS; THE TRIBOLOGICAL BEHAVIOUR OF METALLIC ANTIFRICTION MATERIALS; SIGNIFICANT TERMS
CSA C22.2 No. 60601.2.36 : 2016 MEDICAL ELECTRICAL EQUIPMENT - PART 2-36: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF EQUIPMENT FOR EXTRACORPOREALLY INDUCED LITHOTRIPSY
VDI/VDE/DKD 2638:2008-10 Characteristics of force transducers - Terms and definitions
VDI 3405 Blatt 2:2013-08 Additive manufacturing processes, rapid manufacturing - Beam melting of metallic parts - Qualification, quality assurance and post processing
DIN 51228:1993-07 MATERIALS TESTING MACHINES; FATIGUE TESTING MACHINES; GENERAL REQUIREMENTS
DIN 1072 Beiblatt 1:1988-05 ROAD BRIDGES - DESIGN LOADS - EXPLANATIONS
12/30253196 DC : 0 BS EN 60601-2-36 - MEDICAL ELECTRICAL EQUIPMENT - PART 2-36: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF EXTRACORPOREALLY INDUCED LITHOTRIPSY
IEC 60601-2-36:2014 Medical electrical equipment - Part 2-36: Particular requirements for the basic safety and essential performance of equipment for extracorporeally induced lithotripsy
DIN 50113:1982-03 TESTING OF METALLIC MATERIALS; ROTATING BENDING FATIGUE TEST
EN 60601-2-36:2015 Medical electrical equipment - Part 2-36: Particular requirements for the basic safety and essential performance of equipment for extracorporeally induced lithotripsy

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.