DIN 50979:2008-07
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
METALLIC COATINGS - ELECTROPLATED COATINGS OF ZINC AND ZINC ALLOYS ON IRON OR STEEL WITH SUPPLEMENTARY CR(6)-FREE TREATMENT
Hardcopy , PDF
01-04-2017
English
01-01-2008
Vorwort
1 Anwendungsbereich
2 Normative Verweisungen
3 Bezeichnung
3.1 Galvanische Überzüge
3.2 Passivieren
3.3 Versiegeln
3.4 Wesentliche Flächen (Funktionsfläche)
3.5 Beispiele für Bezeichnungen
4 Bestellangaben
5 Grundwerkstoffe
6 Beschichtungsverfahren/Prozesstechnik
6.1 Vorbehandlung und Abscheidung des
Zink- oder Zinklegierungs-Überzug
6.2 Nachbehandlungen
6.2.1 Passivierungen
6.2.2 Versiegelungen
6.3 Trommel/Gestell (Teilehandling)
6.3.1 Trommelteile
6.3.2 Gestellteile
6.4 Wasserstoffversprödung
6.4.1 Grundlagen
6.4.2 Verfahrensauswahl
7 Anforderungen an die Überzüge und
Prüfmethoden
7.1 Schichtdicke
7.2 Schichthaftung
7.3 Cr(VI)-Freiheit
7.4 Beständigkeit in Kurzzeit-Korrosionsprüfungen
7.4.1 Allgemeines
7.4.2 Mindestbeständigkeiten von passivierten
Zink- bzw. Zinklegierungsüberzügen
8 Prüfbericht
8.1 Allgemeine Angaben
8.2 Besondere Angaben bei Beschichtung von
hochfesten Werkstoffen mit
Zugfestigkeit >/= 1 000 N/mm[2]
8.3 Prüfergebnisse
Literaturhinweise
This standard is included in DIN Handbook 175/2.
DocumentType |
Standard
|
Pages |
14
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Superseded
|
SupersededBy |
BS EN 4710-04:2015 | Aerospace series. Quick release fastening systems for non-structural applications Spring clamp. One way tolerance compensation |
PREN 4710-04 : DRAFT 2014 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL APPLICATIONS - PART 04: SPRING CLAMP - ONE WAY TOLERANCE COMPENSATION |
I.S. EN 4710-05:2015 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL APPLICATIONS - PART 05: SPRING CLAMP - TWO WAYS TOLERANCE COMPENSATION |
BS EN 4710-03:2015 | Aerospace series. Quick release fastening systems for non-structural applications Spring clamp |
NF EN 4710-03 : 2016 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL APPLICATIONS - PART 03: SPRING CLAMP |
DIN 3867:1982-11 | NON-SOLDERING COMPRESSION COUPLINGS - PRESSURE BUSH FOR BUTT JOINTS |
DIN 72571:2016-08 | Fixing clamps - One-sided fastening |
PREN 4710-05 : DRAFT 2014 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL APPLICATIONS - PART 05: SPRING CLAMP - TWO WAYS TOLERANCE COMPENSATION |
DIN 50961:2012-04 | ELECTROPLATED COATINGS - ZINC COATINGS ON IRON OR STEEL - TERMS, TESTING AND CORROSION RESISTANCE |
DIN 3872:2012-02 | NON-SOLDERING COMPRESSION COUPLINGS - UNION NUTS FOR BUTT JOINTS |
I.S. EN 4710-04:2015 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL APPLICATIONS - PART 04: SPRING CLAMP - ONE WAY TOLERANCE COMPENSATION |
I.S. EN 4710-03:2015 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL APPLICATIONS - PART 03: SPRING CLAMP |
EN 4710-03:2015 | Aerospace series - Quick release fastening systems for non-structural applications - Part 03: Spring clamp |
DIN 72573:2016-08 | Fixing clamps - Two-sided fastening |
DIN 3861:2016-09 | NON-SOLDERING COMPRESSION FITTINGS - COMPRESSION RINGS - DESIGN |
NF EN 4710-05 : 2015 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL APPLICATIONS - PART 05: SPRING CLAMP - TWO WAY TOLERANCE COMPENSATION |
DIN 72572:2016-08 | Fixing clamps - Center fastening for 2 lines |
EN 4710-04:2015 | Aerospace series - Quick release fastening systems for non-structural applications - Part 04: Spring clamp - One way tolerance compensation |
EN 4710-05:2015 | Aerospace series - Quick release fastening systems for non-structural applications - Part 05: Spring clamp - Two ways tolerance compensation |
NF EN 4710-04 : 2015 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL APPLICATIONS - PART 04: SPRING CLAMP - ONE WAY TOLERANCE COMPENSATION |
BS EN 4710-05:2015 | Aerospace series. Quick release fastening systems for non-structural applications Spring clamp. Two ways tolerance compensation |
DIN 3867:2012-02 | NON-SOLDERING COMPRESSION COUPLINGS - PRESSURE BUSH FOR BUTT JOINTS |
DIN HDBK 175/2 : 1ED 2013 | |
DIN 2353:2013-01 | NON-SOLDERING COMPRESSION FITTINGS WITH CUTTING RING - COMPLETE FITTINGS AND SURVEY |
DIN EN ISO 2819:2016-10 (Draft) | METALLIC COATINGS ON METALLIC SUBSTRATES - ELECTRODEPOSITED AND CHEMICALLY DEPOSITED COATINGS - REVIEW OF METHODS AVAILABLE FOR TESTING ADHESION |
DIN EN ISO 3497:2001-12 | METALLIC COATINGS - MEASUREMENT OF COATING THICKNESS - X-RAY SPECTROMETRIC METHODS |
DIN EN 15205:2007-02 | DETERMINATION OF HEXAVALENT CHROMIUM IN CORROSION PROTECTION LAYERS - QUALITATIVE ANALYSIS |
DIN EN ISO 2178:2015-01 (Draft) | NON-MAGNETIC COATINGS ON MAGNETIC SUBSTRATES - MEASUREMENT OF COATING THICKNESS - MAGNETIC METHOD (ISO 2178:2016) |
DIN 50969-1:2009-06 | PREVENTION OF HYDROGEN-INDUCED BRITTLE FRACTURE OF HIGH-STRENGTH STEEL BUILDING ELEMENTS - PART 1: ADVICE ON THE PREVENTION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.