Skip to content
Please enter a keyword to search

  • DIN 53519-2:1972-05

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    TESTING OF ELASTOMERS; DETERMINATION OF INDENTATION HARDNESS OF SOFT RUBBER (IRHD); HARDNESS TESTING ON SPECIMENS OF SMALL DIMENSIONS, MICRO-TESTING

    Available format(s):  Hardcopy, PDF

    Superseded date:  01-07-2003

    Language(s):  English

    Published date:  12-01-2013

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add To Cart

    Abstract - (Show below) - (Hide below)

    This method is used for measuring indentation hardness in the 'normal' sub-range on specimens which, because of their small dimensions, cannot be measured according to DIN 53519 Sheet 1. It should be borne in mind that any existing inhomogeneity, surface hardening, unevenness or roughness (e.g. through buffing) will exert a considerably greater influence on the outcome of the micro-testing that on the results of testings performed according to Sheet 1. Therefore, even when standard specimens are used, complete agreement between the values measured by the two methods cannot always be expected.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    DIN 52292-2:1986-09 TESTING OF GLASS AND GLASS CERAMICS; DETERMINATION OF BENDING STRENGTH; COAXIAL DOUBLE RING BENDING TEST OF A FLAT TEST PIECE WITH LARGE TEST AREA
    DIN 52290-4:1988-11 SECURITY GLAZING - TESTING OF THE RESISTANCE AGAINST PENETRATION BY BALLS AND CLASSIFICATION
    DIN 52292-1:1984-04 TESTING OF GLASS AND GLASS CERAMICS; DETERMINATION OF BENDING STRENGTH; COAXIAL DOUBLE RING BENDING TEST ON FLAT SPECIMENS WITH SMALL TEST AREA
    DIN 3771-2:1984-12 FLUID SYSTEMS; O-RINGS; TEST, MARKING
    DIN 52307:1990-03 DART DROP TEST ON SAFETY GLASS FOR VEHICLE GLAZING
    DIN IEC 60544-2 : 1996 GUIDE FOR DETERMINING THE EFFECTS OF IONIZING RADIATION ON INSULATING MATERIALS - PART 2: PROCEDURES FOR IRRADIATION AND TEST
    DIN 3761-12:1984-01 ROTARY SHAFT LIP TYPE SEALS FOR AUTOMOBILES; TEST; DETERMINATION OF INDENTATION HARDNESS OF ELASTOMERS; MICRO HARDNESS TEST
    DIN EN ISO 3822-4:1997-03 ACOUSTICS - LABORATORY TESTS ON NOISE EMISSION FROM APPLIANCES AND EQUIPMENT USED IN WATER SUPPLY INSTALLATIONS - PART 4: MOUNTING AND OPERATING CONDITIONS FOR SPECIAL APPLIANCES
    DIN 52290-3:1984-06 ATTACK-BLOCKING GLAZINGS; TESTING OF THE RESISTANCE AGAINST BREAK BY MEANS OF A CUTTING STRIKING TOOL AND CLASSIFICATION
    DIN 52306:1990-03 BALL DROP TEST ON SAFETY GLASS FOR VEHICLE GLAZING
    DIN EN 549:1995-04 RUBBER MATERIALS FOR SEALS AND DIAPHRAGMS FOR GAS APPLIANCES AND GAS EQUIPMENT
    DIN 53538-6:1993-08 STANDARD REFERENCE ELASTOMERS - HYDROGENATED ACRYLONITRILE BUTADIENE RUBBER (HNBR), CROSS-LINKED BY PEROXIDE, FOR CHARACTERIZING SERVICE FLUIDS WITH RESPECT TO THEIR ACTION ON HNBR
    DIN EN 50014 : 2000 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - GENERAL REQUIREMENTS
    VDE 0620-101 : 1992 PLUGS AND SOCKET-OUTLETS UP TO 400 V 25 A; FLAT NON-WIRABLE TWO POLE PLUGS, 2.5 A 250 V, WITH CORD, FOR THE CONNECTION OF CLASS-2-EQUIPMENT FOR HOUSEHOLD AND SIMILAR PURPOSES
    DIN 65271:2002-07 AEROSPACE SERIES - ELASTOMERIC SEMI-FINISHED PRODUCTS AND PARTS - TECHNICAL SPECIFICATION
    DIN 52310:1986-07 HEADFORM IMPACT TEST ON SAFETY GLASS FOR VEHICLE GLAZING
    DIN VDE 0620-101 : 1992 PLUGS AND SOCKET-OUTLETS UP TO 400 V 25 A; FLAT NON-WIRABLE TWO POLE PLUGS, 2,5 A 250 V, WITH CORD, FOR THE CONNECTION OF CLASS-2-EQUIPMENT FOR HOUSEHOLD AND SIMILAR PURPOSES
    DIN 52303-1:1984-08 TEST METHODS FOR FLAT GLASS IN BUILDINGS; DETERMINATION OF BENDING STRENGTH; TESTING WITH RESTING ON TWO SUPPORTS
    DIN EN 1081:1998-04 RESILIENT FLOOR COVERINGS - DETERMINATION OF THE ELECTRICAL RESISTANCE
    DIN EN 1123-1:1999-03 PIPES AND FITTINGS OF LONGITUDINALLY WELDED HOT-DIP GALVANIZED STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 1: REQUIREMENTS, TESTING, QUALITY CONTROL
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective