DIN 65149:1980-12
Current
The latest, up-to-date edition.
AEROSPACE; SCREWS OF STEEL FOR NON-STRUCTURAL COMPONENTS, M3 AND M4, TECHNICAL SPECIFICATION
Hardcopy , PDF
German
01-01-1980
1 Anwendungsbereich
2 Mitgeltende Normen und Unterlagen
3 Begriffe
4 Anforderungen
4.1 Werkstoff
4.2 Gestaltung und Massen
4.2.1 Masse
4.2.2 Gewinde
4.2.3 Form- und Lagetoleranzen
4.2.4 Massen
4.3 Fertigungsbedingte Eigenschaften
4.3.1 Oberflächenrauheit
4.3.2 Oberflächenbehandlung
4.4 Mechanische Eigenschaften
4.4.1 Zugbruchkraft
4.4.2 Härte
4.5 Metallurgische Eigenschaften
4.5.1 Mikro-Gefüge
4.5.2 Faserverlauf
4.5.3 Permeabilität
4.6 Kennzeichnung
4.6.1 Kennzeichnung des Erzeugnisses
4.6.2 Kennzeichnung der Verpackung
5 Prüfung
5.1 Werkstoff
5.2 Gestaltung und Massen
5.2.1 Masse
5.2.2 Gewinde
5.2.3 Form- und Lagetoleranzen
5.2.4 Massen
5.3 Fertigungsbedingte Eigenschaften
5.3.1 Oberflächenrauheit
5.3.2 Oberflächenbehandlung
5.4 Mechanische Eigenschaften
5.4.1 Zugbruchkraft
5.4.2 Härte
5.5 Metallurgische Eigenschaften
5.5.1 Mikro-Gefüge
5.5.2 Faserverlauf
5.5.3 Permeabilität
5.6 Kennzeichnung
5.6.1 Kennzeichnung des Erzeugnisses
5.6.2 Kennzeichnung der Verpackung
6 Abnahmeprüfung
6.1 Allgemeines
6.2 Bescheinigung der Prüfergebnisse
6.3 Statistische Qualitätskontrolle und
abweichende Probenbeurteilung
6.4 Fertigungskontrolle und Fertigungsbeobachtung
7 Verpackung
7.1 Grundpackung
7.2 Sammelpackung
7.3 Versandpackung
Diese Norm gilt für Schrauben mit Gewinde M 3 und M 4, die für nichttragende Bauteile in der Luft- und Raumfahrt angewendet werden.
DocumentType |
Standard
|
Pages |
20
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Current
|
DIN 65523:1984-07 | Aerospace; hexagon bolts, with MJ-thread, short thread, corrosion-resisting steel, nominal tensile strength 700 MPa, for temperatures up to 425 C |
DIN 65520:1984-07 | Aerospace; pan head bolts, close tolerance, with ribbed TORQ-SET (ACR) recess an MJ-thread, short thread, steel, nominal tensile strength 900 MPa, for temperatures up to 235 C |
DIN 65516:1984-07 | AEROSPACE - CHEESE HEAD BOLTS WITH INTERNAL SERRATION THREAD, SHORT THREAD, STEEL, NOMINAL TENSILE STRENGTH 900 MPA, FOR TEMPERATURES UP TO 235 DEGREES C |
DIN 65267:1992-09 | AEROSPACE; SCREWS, HEXAGON, WITH MJ THREAD, THREADED APPROXIMATELY TO HEAD, STEEL, NOMINAL TENSILE STRENGTH 900 MPA, FOR TEMPERATURES UP TO 235 DEGREES CENTIGRADE |
DIN 65522:1984-07 | AEROSPACE - SCREWS, HEXAGON, WITH MJ-THREAD, THREADED APPROXIMATELY TO HEAD, CORROSION-RESISTING STEEL, NOMINAL TENSILE STRENGTH 700 MPA, FOR TEMPERATURES UP TO 425 DEGREES C |
DIN 65519:1984-07 | Aerospace; pan head bolts with ribbed TORQ-SET (ACR) recess and MJ-thread, short thread, steel, nominal tensile strength 900 MPa, for temperatures up to 235 C |
DIN 65502:1984-07 | AEROSPACE - PAN HEAD BOLTS WITH RIPPED TORQ-SET (ACR) RECESS AND MJ-THREAD, SHORT THREAD, CORROSION-RESISTING STEEL, NOMINAL TENSILE STRENGTH 700 MPA, FOR TEMPERATURES UP TO 425 DEGREES C |
WL 1.1174 : 1978 | UNALLOYED HEAT-TREATABLE STEEL WITH ABOUT 0.35C - RODS AND FORGINGS |
DIN ISO 898-1:1989-01 | MECHANICAL PROPERTIES OF FASTENERS - BOLTS, SCREWS AND STUDS |
DIN 7160:1965-08 | ISO-DEVIATIONS FOR SHAFTS FOR SIZES FROM 1 TO 500 MM |
LN 65018-1:1968-09 | Manufacturers certification for screws and bolts |
DIN 50150:2000-10 | TESTING OF METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES |
MIL-I-17214 Revision B:1984 | INDICATOR, PERMEABILITY, LOW-MU (GO-NO-GO) |
DIN 55511-1:1984-12 | MEANS OF PACKAGING; BOXES MANUFACTURED FROM SOLID FIBRE-BOARD OR CORRUGATED BOARD, ADJUSTED TO 600 MM X 400 MM (AREA MODULE); FOLDING BOXES WITH BOTTOM AND TOP FLAPS |
WL 1.7220 : 1992 | HEAT-TREATABLE CHROMIUM-MOLYBDENUM STEEL WITH ABOUT 0,35C-1CR-0,2MO; RODS AND WIRE FOR SCREWS AND NUTS TO BE COLD-FORMED OR HOT-FORMED |
DIN 50950:1984-10 | MEASUREMENT OF COATING THICKNESS; MICROSCOPIC MEASUREMENT OF COATING THICKNESS; CROSS SECTION METHOD |
DIN 50133-1:1972-12 | TESTING OF METALLIC MATERIALS; VICKERS HARDNESS TEST; RANGE HV 0,2 TO HV 100 |
DIN 50351:1985-02 | TESTING OF METALLIC MATERIALS - BRINELL HARDNESS TEST |
DIN 17440:2001-03 | STAINLESS STEELS - TECHNICAL DELIVERY CONDITIONS FOR DRAWN WIRE |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.