DIN 9015-1:1986-12
Current
The latest, up-to-date edition.
AEROSPACE; ISO-FITS FOR AIRFRAME CONSTRUCTION (EXCEPT MOUNTING OF ROLLER BEARINGS)
Hardcopy , PDF
German
01-01-1986
Kein Inhaltsverzeichnis in der Norm vorhanden.
Diese Norm soll bei der Auswahl von Passtoleranzen und Toleranzfeldkombinationen für die Belange des Zellenbaus der Luft- und Raumfahrt angewendet werden und dazu dienen, die Vielfalt der möglichen Kombinationen der ISO/R 286 - 1962 einzuschränken, um die Anzahl der Werkzeuge, Lehren und Messgeräte auf eine geringe Menge zu begrenzen. Die in Tabelle 1 ausgewählten Toleranzfelder können beliebig gepaart werden. Jedoch wird empfohlen, diejenigen Paarungen zu wählen, die in Tabelle 2 zusammengestellt wurden und deren Abmasse berechnet vorliegen. Aus Gründen der Wirtschaftlichkeit sollte nur in Sonderfällen von den in dieser Norm empfohlenen Toleranzfeldern und Toleranzfeldkombinationen abgewichen werden.
DocumentType |
Standard
|
Pages |
5
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Current
|
DIN 9015-2:1986-12 | AEROSPACE; ISO-FITS FOR ENGINE CONSTRUCTION (EXCEPT MOUNTING OF ROLLER BEARINGS) |
DIN 7161:1965-08 | ISO-DEVIATIONS FOR HOLES FOR SIZES FROM 1 TO 500 MM |
DIN 7150-1:1966-06 | ISO SYSTEM OF LIMITS AND FITS FOR SIZES FROM 1 TO 500 MM - INTRODUCTION |
DIN 7190:2001-02 | INTERFERENCE FITS - CALCULATION AND DESIGN RULES |
DIN 7182-1 : 1986 | SIZES, DEVIATIONS, TOLERANCES AND FITS; BASIC CONCEPTS |
DIN 7172-3 : 1986 | TOLERANCES AND LIMIT DEVIATIONS FOR SIZES ABOVE 500 MM UP TO AND INCLUDING 10000 MM - PRINCIPLES |
DIN 7160:1965-08 | ISO-DEVIATIONS FOR SHAFTS FOR SIZES FROM 1 TO 500 MM |
DIN 7152 : 1965 | ISO FUNDAMENTAL DEVIATIONS FOR SIZES FROM 1 TO 500 MM |
DIN 7151:1964-11 | ISO STANDARD TOLERANCES FOR SIZES FROM 1 TO 500 MM |
DIN 7172-2:1986-03 | TOLERANCES AND LIMIT DEVIATIONS FOR SIZES ABOVE 500 MM UP TO AND INCLUDING 10000 MM - LIMIT DEVIATIONS |
DIN 7182-3 : 1977 | LIMITS AND FITS, INTERFERENCE FITS, TERMS AND DEFINITIONS |
DIN 7155-2:1966-08 | ISO-FITS FOR THE SHAFT BASIS SYSTEM; TOLERANCES OF FIT (CLEARANCES AND INTERFERENCES) |
DIN 7168-1:1981-05 | GENERAL TOLERANCES - LINEAR AND ANGULAR DIMENSIONS |
DIN 7155-1:1966-08 | ISO-FITS FOR THE SHAFT BASIS SYSTEM; TOLERANCE ZONES, DEVIATIONS |
DIN 9015-2:1986-12 | AEROSPACE; ISO-FITS FOR ENGINE CONSTRUCTION (EXCEPT MOUNTING OF ROLLER BEARINGS) |
DIN 7172-1 : 1986 | TOLERANCES AND LIMIT DEVIATIONS FOR SIZES ABOVE 500 MM UP TO AND INCLUDING 1000 MM - FUNDAMENTAL TOLERANCES |
DIN 7154-1:1966-08 | ISO-FITS FOR THE HOLE BASIS SYSTEM; TOLERANCE ZONES, DEVIATIONS |
DIN 7154-2:1966-08 | ISO-FITS FOR THE HOLE BASIC SYSTEM; TOLERANCES OF FIT (CLEARANCES AND INTERFERENCES) |
ISO/R 286:1962 | ISO system of limits and fits Part I : General, tolerances and deviations |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.