DIN 9015-2:1986-12
Current
The latest, up-to-date edition.
AEROSPACE; ISO-FITS FOR ENGINE CONSTRUCTION (EXCEPT MOUNTING OF ROLLER BEARINGS)
Hardcopy , PDF
German
01-01-1986
Important note : Users cannot be edited or removed once added to your Multi user PDF.Kein Inhaltsverzeichnis in der Norm vorhanden.
Diese Norm soll bei der Auswahl von Passtoleranzen und Toleranzfeldkombinationen für die Belange des Triebwerkbaus der Luft- und Raumfahrt angewendet werden und dazu dienen, die Vielfalt der möglichen Kombinationen der ISO/R 286 - 1962 einzuschränken, um die Anzahl der Werkzeuge, Lehren und Messgeräte auf eine geringe Menge zu begrenzen. Die in den Tabellen 1 und 2 ausgewählten Toleranzfelder können beliebig gepaart werden. Jedoch wird empfohlen, diejenigen Paarungen zu wählen, die in den Tabellen 3 und 4 zusammengestellt wurden und deren Abmasse berechnet vorliegen. Aus Gründen der Wirtschaftlichkeit sollte nur in Sonderfällen von den in dieser Norm empfohlenen Toleranzfeldern und Toleranzfeldkombinationen abgewichen werden.
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Current
|
| DIN 9015-1:1986-12 | AEROSPACE; ISO-FITS FOR AIRFRAME CONSTRUCTION (EXCEPT MOUNTING OF ROLLER BEARINGS) |
| DIN 7161:1965-08 | ISO-DEVIATIONS FOR HOLES FOR SIZES FROM 1 TO 500 MM |
| DIN 7150-1:1966-06 | ISO SYSTEM OF LIMITS AND FITS FOR SIZES FROM 1 TO 500 MM - INTRODUCTION |
| DIN 7190:2001-02 | INTERFERENCE FITS - CALCULATION AND DESIGN RULES |
| DIN 7182-1 : 1986 | SIZES, DEVIATIONS, TOLERANCES AND FITS; BASIC CONCEPTS |
| DIN 7172-3 : 1986 | TOLERANCES AND LIMIT DEVIATIONS FOR SIZES ABOVE 500 MM UP TO AND INCLUDING 10000 MM - PRINCIPLES |
| DIN 7160:1965-08 | ISO-DEVIATIONS FOR SHAFTS FOR SIZES FROM 1 TO 500 MM |
| DIN 7152 : 1965 | ISO FUNDAMENTAL DEVIATIONS FOR SIZES FROM 1 TO 500 MM |
| DIN 7151:1964-11 | ISO STANDARD TOLERANCES FOR SIZES FROM 1 TO 500 MM |
| DIN 7172-2:1986-03 | TOLERANCES AND LIMIT DEVIATIONS FOR SIZES ABOVE 500 MM UP TO AND INCLUDING 10000 MM - LIMIT DEVIATIONS |
| DIN 7182-3 : 1977 | LIMITS AND FITS, INTERFERENCE FITS, TERMS AND DEFINITIONS |
| DIN 7155-2:1966-08 | ISO-FITS FOR THE SHAFT BASIS SYSTEM; TOLERANCES OF FIT (CLEARANCES AND INTERFERENCES) |
| DIN 7168-1:1981-05 | GENERAL TOLERANCES - LINEAR AND ANGULAR DIMENSIONS |
| DIN 7155-1:1966-08 | ISO-FITS FOR THE SHAFT BASIS SYSTEM; TOLERANCE ZONES, DEVIATIONS |
| DIN 7172-1 : 1986 | TOLERANCES AND LIMIT DEVIATIONS FOR SIZES ABOVE 500 MM UP TO AND INCLUDING 1000 MM - FUNDAMENTAL TOLERANCES |
| DIN 7154-1:1966-08 | ISO-FITS FOR THE HOLE BASIS SYSTEM; TOLERANCE ZONES, DEVIATIONS |
| DIN 7154-2:1966-08 | ISO-FITS FOR THE HOLE BASIC SYSTEM; TOLERANCES OF FIT (CLEARANCES AND INTERFERENCES) |
| ISO/R 286:1962 | ISO system of limits and fits Part I : General, tolerances and deviations |
| DIN 9015-1:1986-12 | AEROSPACE; ISO-FITS FOR AIRFRAME CONSTRUCTION (EXCEPT MOUNTING OF ROLLER BEARINGS) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.