Foreword to EN 1:1998
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 Constructional requirements
4.1 Heating capacity
4.2 Materials
4.3 Combustion chamber
4.4 Filter
4.5 Oil regulator
4.6 Marking of operating settings
4.7 Safety device
4.8 Fan for the supply of combustion air
4.9 Fuel lines
4.10 Built-in storage tank
4.11 Oil-level indicator
4.12 Drip tray
4.13 Flue outlet
4.14 Damper
4.15 Draught regulators and combustion air limiters
4.16 Assembly
4.17 Maintenance
4.18 Additional requirements for appliances with
automatic burners
5 Performance and operating requirements
5.1 Maximum oil flow
5.2 Minimum oil flow
5.3 Ignition
5.4 Appliance classes for efficiency and emissions
5.5 Smoke number
5.6 Flue gas temperature
5.7 Carbon monoxide content of the flue gas
5.8 Oil temperature
5.9 Floor temperature
5.10 Wall temperature
5.11 Temperature of the control knobs
5.12 Electrical safety
5.13 NO[X] and unburnt hydrocarbons (C[n]H[m]) in the
flue gases
6 Tests
6.1 Test apparatus
6.1.1 General
6.1.2 Testing of stoves having several possible
outlet connections
6.2 Test fuel
6.3 Verification of construction
6.4 Testing of leak-tightness of the fuel circuit
6.5 Operational tests
6.5.1 Short-term tests
6.5.2 Long-term tests
6.5.3 Additional tests
6.5.4 Measurement methods
6.6 Calculations from the measurements
6.6.1 Efficiency
6.6.2 Heating capacities
6.6.3 Carbon monoxide content of the flue gases
6.6.4 NO[x] in the flue gas
6.6.5 Unburnt hydrocarbons in the flue gas
6.6.6 Flue gas mass flow rate
6.6.7 Symbols and units
6.7 Test report
7 Instructions and marking of the appliance
7.1 General
7.2 Installation instructions
7.3 User operating instructions
7.4 Marking
7.5 Documentation for the production
8 Evaluation of conformity
8.1 General
8.2 Type testing
8.2.1 Initial type testing
8.2.2 Further type testing
8.3 Factory production control (FPC)
8.3.1 General
8.3.2 Raw materials and components
8.3.3 Control of inspection, measuring and test equipment
8.3.4 Process control
8.3.5 Product inspection, testing and evaluation
8.3.6 Manufacturing checks
8.3.7 Non conforming products
8.3.8 Corrective and preventive action
8.3.9 Handling, storage, packaging, preservation
and delivery
Annex A (normative) Measuring method for determining
the smoke number
A.1 Equipment required for the determination of the
smoke number
A.1.1 Pump
A.1.2 Sampling tube
A.1.3 Filter paper
A.1.4 Grey scale
A.2 Determination of the smoke number
Annex B (normative) Fluid method for detecting oil derivatives
B.1 Equipment required for the detection of oil derivatives
B.1.1 Pump
B.1.2 Sampling tube
B.1.3 Filter paper
B.1.4 Fluid
B.1.5 Sampling
B.1.6 Procedure and evaluation
Annex C (normative) Measurement of nitrogen oxides
C.1 General objective and applicability
C.2 General procedure
C.3 Measuring principles of analysers
Annex D (normative) Measurement of total hydrocarbons (THC)
D.1 General objective and applicability
D.2 General procedure
D.3 Equipment
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirement
of EU Directive 89/106/EEC, EU
Construction Products Directive
ZA.1 Scope and relevant characteristics
ZA.2 Procedure for the attestation of conformity of
oil stoves
ZA.2.1 System of attestation of conformity
ZA.2.2 Declaration of conformity
ZA.3 CE Marking and labelling
Bibliography