DIN EN 12067-1 : 1998 AMD 1 2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 1: PNEUMATIC TYPES
01-06-2011
12-01-2013
Foreword
1 Scope
2 Normative references
3 Definitions
4 Construction requirements
5 Performance requirements
6 Test methods
7 Instructions and declarations
8 Marking
Annexes
A (informative) - Use of ISO 7-1: 1994 and ISO 228-1: 1994
threads for gas connections
B (informative) - Leak tightness test - volumetric method
C (informative) - Leak tightness test - pressure loss method
D (informative) - Conversion of pressure loss into leakage
rate
ZA (informative) - Clauses of this European Standard
addressing essential requirements or other provisions
of EU Directives
Describes the safety, construction and performance requirements for gas/air ratio controls for inlet pressures up to and including 500 mbar of nominal connection size up to and including DN 150, intended for use with gas appliances used with one or more fuel gases of the first, second and third families. Also describes the test procedures for evaluating these requirements and defines information necessary for use and installation.
| DevelopmentNote |
Supersedes DVGW VP 106. (11/2003)
|
| DocumentType |
Standard
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNE-EN 12067-1:1999 | Identical |
| NBN EN 12067-1 : 99 AMD 1 2003 | Identical |
| UNI EN 12067-1 : 2006 | Identical |
| BS EN 12067-1:1999 | Identical |
| SN EN 12067-1 : 1999 AMD 1 2003 | Identical |
| NF EN 12067-1 : 98 AMD 1 2003 | Identical |
| NEN EN 12067-1 : 1998 AMD 1 2003 | Identical |
| I.S. EN 12067-1:1999 | Identical |
| EN 12067-1 : 98 AMD 1 2003 | Identical |
| NS EN 12067-1 : 1999 AMD 1 2003 | Identical |
| EN 60998-2-2:2004 | Connecting devices for low-voltage circuits for household and similar purposes - Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units |
| ISO 274:1975 | Copper tubes of circular section — Dimensions |
| EN 60998-2-1:2004 | Connecting devices for low-voltage circuits for household and similar purposes - Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units |
| EN 161:2011+A3:2013 | Automatic shut-off valves for gas burners and gas appliances |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 301:2006 | Zinc alloy ingots intended for castings |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.